A five-cylinder, 3.5-liter SI engine operates on a four-stroke cycle at 2500 RPM. At this condition, the mechanical efficiency of the engine is 62% and 1000 J of indicated work are produced each cycle in each cylinder. Calculate: (a) Indicated mean effective pressure. [kPa] (b) Brake mean effective pressure. [kPa] (c) Friction mean effective pressure. [kPa] (d) Brake power in kW and hp. (e) Torque. [N-m]

A five-cylinder, 3.5-liter SI engine operates on a four-stroke cycle at 2500 RPM. At this condition, the mechanical efficiency of the engine is 62% and 1000 J of indicated work are produced each cycle in each cylinder. Calculate: (a) Indicated mean effective pressure. [kPa] (b) Brake mean effective pressure. [kPa] (c) Friction mean effective pressure. [kPa] (d) Brake power in kW and hp. (e) Torque. [N-m]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

14. What is a Moody Chart used to determine? 15. Express a volume of 0.375 litres in Sl units 16. What is the name given to the shape of the velocity profile of a fluid flowing in a turbulent manner through a pipe? Provide a sketch of this profile. 17. Write an expression relating mass flow rate to the velocity of a fluid. 18. State the conditions required for a stoichiometric combustion reaction. 19. What would be the products of combustion from the stoichiometric combustion of a hydrocarbon fuel? 20. Using the steam tables, what is the value of specific enthalpy of saturated liquid water at 200 kPa? 21. Name two thermodynamic properties that may be found in steam tables. 22. What does the term emissivity mean? 23. Name one characteristic of a surface with low emissivity? 24. Explain the difference between natural and forced convection 25. Express a pressure of 200 milli-bar in Pa 26. What are the units for the overall heat transfer coefficient, U? 27. As a hot air balloon rises, the…
A fuel oil C8H18 is used in an internal combustion engine and the Orsat analysis are as follows: CO2 = 12.8% ; O2 = 3.5%; CO = 0.2% and N2 = 83.5%. Determine the actual air-fuel ratio.
10) Which one of the following statements is incorrect about a catalytic converter? O It is not very efficient at lower temperatures. O Its NOx conversion efficiency is highest for very lean mixtures. O Its CO conversion efficiency is high for lean mixtures. O Lead reduces its effectiveness. 11) Which one of the following is true about a particulate trap? O It is predominantly used in Sl engines. O It does not offer a restriction to exhaust flow. O It requires periodic regeneration. O It is predominantly used to reduce NOx emissions.
9
Mention two advantages for preferring MCG over diesel as an automobile fuel .
In 4-stroke Cl engines, the ignition induced by O hot coolant. O lubrication oil. O exhaust valve. O fuel tank. O spark plug. O high temperature due to high pressure ratio.
From environmental point of view, why over cooling of automobile engines is not recommended?
True or False? In an HCCI engine, combustion immediatelyand simultaneously produces a steady flameacross the mixture.
The instrument needed for the ts engine is---- for ignition system-- for fuel system- --and electric system-- Vacuum gauge, Ohm meter, Voltmeter, Compression gauge Vacuum gauge, Ohm meter, Fuel pump, Ammeter Vacuum gauge, Tachometer, Fuel pump, Gas analyzer Vacuum gauge, Ohm meter, Fuel pump, Thermometer O Skip
??
Determine the air fuel ratio on both a molar and mass basis for the complete combustion of Octane (C8H18) with: (a) the theoretical amount of air. ( b) 50% excess air.
7. Describe the difference(s), if any, between pre-mixed and diffusion type combustion. Please select all answers that apply: a) In pre-mixed type combustion, the fuel and oxidizer are mixed before entering the combustion chamber. b) In diffusion type combustion the fuel and oxidizer enter the combustion chamber from two separate inlet streams. c) In pre-mixed combustion the fuel and oxidizer enter the combustion chamber through a single stream. d) In diffusion combustion, the fuel is injected through a nozzle. e) In diffusion combustion, the oxidizer swirls around the fuel nozzle.