A fish is reeled in at a rate of 2.5 feet per second from a point 10 feet above the water (see figure). At what rate is the angle between the line and the water changing when there is atotal of 25 feet of line out? (Round your answer to three decimal places.)dedtrad/sec10 ft

Answered: Image /qna-images/answer/01a002c7-40e3-4556-9a34-e969d81a6b21.jpg

Answered: A fish is reeled in at a rate of 2.5…

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter57: Fundamental Geometric Constructions

Section: Chapter Questions

Problem 5A: A carbide milling cutter is used for machining a 27.25-inch length of stainless steel. The cutting...

See similar textbooks

Similar questions

Find the intensity of light at a depth of 12 meter if I0=14 and k=0.7. Round to two decimals.
Refer to the following figure in answering Exercises 7 through 13. It may be helpful to sketch figures.When side x= side y. a. What is the value of 1 ? b. What is the value of the tangent function? c. What is the value of the cotangent function?
A plug gage tapers 3.10 mm along a 38.00 mm length, as shown in Figure 215. Set up a proportion and determine the amount of taper in the workpiece for each of the following problems. Express the answers to 2 decimal places.
A single-threaded (or single-start) square-thread screw is shown in Figure 5-6. The lead of a screw is the distance that the screw advances in one turn (revolution). The lead is equal to the pitch in a single-threaded screw. Given the number of turns and the amount of screw advance, determine the leads.
Find radius r. All dimensions are in millimeters.
The carbon content of machine steel for gages usually ranges from 0.15% to 0.25%. Round the answers for a and b to 2 decimal places. a. What is the minimum weight of carbon in 250 kilograms of machine steel? b. What is the maximum weight of carbon in 250 kilograms of machine steel?
A carbide milling cutter is used for machining a 27.25-inch length of stainless steel. The cutting time is 12.35 minutes, the cutting speed is 240 feet per minute, and the feed is 0.01 inches per revolution. What is the diameter of the carbide milling cutter? Round the answer to 2 decimal places.
Velocity at the Equator Assuming the radius of the earth is 4,000 miles, use the information from Problem 43 to find the linear velocity of a person standing on the equator.
A piece shown by the shaded portion is to be cut from a square plate 128 millimeters on a side. a. Compute the area of the piece to be cut. Round the answer to the nearest square millimeter. b. After cutting the piece, determine the percentage of the plate that will be wasted.

Recommended textbooks for you

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Algebra: Structure And Method, Book 1

Algebra

ISBN:

9780395977224

Author:

Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole

Publisher:

McDougal Littell

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Algebra: Structure And Method, Book 1

Algebra

ISBN:

9780395977224

Author:

Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole

Publisher:

McDougal Littell

College Algebra (MindTap Course List)

Algebra

ISBN:

9781305652231

Author:

R. David Gustafson, Jeff Hughes

Publisher:

Cengage Learning

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781305652224

Author:

Charles P. McKeague, Mark D. Turner

Publisher:

Cengage Learning

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

SEE MORE TEXTBOOKS

A fish is reeled in at a rate of 2.5 feet per second from a point 10 feet above the water (see figure). At what rate is the angle between the line and the water changing when there is a total of 25 feet of line out? (Round your answer to three decimal places.) de dt rad/sec 10 ft