a) Find the settling time, peak time, percent overshot for the following systemG(s)= 1s2+b1s+bo'-; close loop system with b, = 1, bo = 6b)Speed control of a dc motor using PID controller

We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Answered: a) Find the settling time, peak time,…

a) Find the settling time, peak time, percent overshot for the following system G(s)=- s2+b1s+bo close loop system with b, = 1, bo = 6

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

Kindly solve what is ask with complete solution and circuit diagram so that I can understand it clearly. I want a handwritten solution. Thank youuu!!
9-In a the shunt field winding is connected in parallel with the armature winding only. Ish Series . Field EJR Shunt Rsh Rse Field 10-The consist of and 11- E = (V – IaRa ) then N = LOAD
Q6/ Answer the following questions: 1. Define the DC motor drive 2. Classify the DC motor drive 3. How can be controlling on the speed of DC motor 4. Numerate the types of AC-DC converter 5. Draw the circuit of single -phase converter on separately excited DC motor 6. Write the equations the following: I. Speed(W)= II. Torque developed(Td): III. Vm=..
1) Derive the transfer function of Amature controlled DC shunt motor
A hybrid stepper motor is shown in Figure Q2(b). Demonstrate how the windings of the stepper motor are excited in wave drive mode to rotate the rotor 4 steps in the counterclockwise direction. Assume that Figure Q2(b) shows the starting position (to) of the stepper motor before the windings are excited. The first step (41) is given in Table Q2(b). (Note: Transfer Table Q2(b) to the answer script; tick the correct cells in the table to show the winding excitation sequence.) (b) Table Q2(b) Clock cycle Stator pole North pole South pole i (s) t2 (s) Al A2 B1 B2 Al A2 B1 B2 Clock eyele в (s) A2 14 (s) Stator pole North pole South pole AI B1 B2 Al A2 B1 B2 stator A1 AL armature N shaft PM armature 1- amature 2 armature 2 A A2 Figure Q2(b)
1) P.f of inductive load is corrected by connecting . . across it. .... ...... 2) Open circuit test measures . losses. 3) The output variables of a motor are and ........ ... .... 4) For a motor output power is given by ...... 5) Flux control, voltage control, and armature control are three methods for ....... of dc motor. 6) A transformer takes 100V at primary and gives 50V at secondary, its turn ratio equals 7) The given set of equations represents . . Ea – laRa = Vr , la = IL , %3D Rf 8) The given set of equations represents. la = !, + IL, VT Rf Ea – laRa = Vr , 9) The given set of equations represents . Ea – laRa – IseRse = Vr, la = Ise = l, %3D | 10). .. has more initial torque than shunt dc motor.
Q4) What is the effect in series motor if you assume V = Eb , with low resistance fielding winding ? a) b) The given information about series motor on full – load (with that the flux is proportional to the field current) is a ) takes ( 78A) and runs at (850 r.p.m) , the series winding resistance is (0.04 2) , with diverter in parallel with the field winding is a (0.18 2) and the armature resistance is (0.09 S2). ( 220 V Neglected the iron, friction and windage losses. Determine the efficiency , speed when developing full load torque ,the maximum efficiency .
Kindly solve what is ask with complete solution and circuit diagram so that I can understand. I want a handwritten solution and write the givens. Thank you very much ma'am/sir..
1-The power output of the three phase machine is greater than the single phase machine. (TRUE/FALSE) 2-In thermocouple, when both the junctions are at the same temperature, the potential difference developed across both junction is zero. (TRUE/FALSE) 3-Due to decreased armature m.m.f., the armature reaction during load condition will increase and hence field flux will be distorted. (TRUE/FALSE) 4-While applying voltage in CRO, the grid is positive with respect to cathode. (TRUE/FALSE) 5-Losses in transformers are generally low and thus efficiency is high. (TRUE/FALSE)
نقطتان )2( Q1// An 8 pole duplex lap winding will have ............. parallel path 8 O 32 O 16 نقطتان )2( Q2//the armature of a dc * machine is made of silicon steel O cast steel O soft iron wrought iron O
A shunt DC motor is supplied by 520V terminals voltage and is used to supply a mechanical load with rotating speed of 1000rpm. The armature is wave-wound and has 500 conductors. The useful flux per pole is 0.03Wb and there are 4 poles (2 pairs of poles). The armature resistance is 0.4 Ohms. Calculate: 1.The internal emf of the motor. 2.The armature current. CLEAR AND CORRECT OR DISLIKE
Q27/ (a) With necessary diagram, explain the working principle of dc motor