a) Find ib in DC analysis= b) Find ic in DC analysis= c) Find Vce in DC analysis=

Q: Given the circuit in figure below, find the z parameter. 1. Is 32

A:

Q: If we are using the following cireuit to measure ECG signal, V* has I mV of 60HZ noise and ECG…

A: Modified circuit is – Voltage of inverting and non – inverting input terminal of every op-amp is…

Q: ?What is the practical model for zener diode

A: A simple question based on zener diode model for practical use. The explanation is provided below…

Q: Don't do the inverse z transformation, find the initial and final values. 2(2 – 0.25) x - 0.52 +0.25…

A: Given, Z Transform

Q: Why do we prefer SSB transmission? Explain the advantages give formulas and numerical example.…

A: In SSB Transmission, Noise present in the signal is less as compared to DSB transmission as well as…

Q: What is the difference of the readings between B/A and A/B sections in the oscilloscope of Multisim?

A: If we taken voltage across a-b terminal is =+(positive some voltage) If we taken voltage across b-a…

Q: Consider the Circuit below: VCC R1 RC Q1 RE

A:

Q: Q Given Vs808, V, assuming free space conditaus, find @ ED the Volume chargedensity atpzo-5 th tal…

A:

Q: - An experimenter uses a 10-bit A/D having a range from -5 [V] to +5 [V] to digitize a 35.0 [mV]…

A:

Q: Refer to the following figure. If IB=7S LA, BDC = 100, 43DI%3D VCC 20 V, and RC=15 kN the value of…

A:

Q: Course: Data Networks - ECTE201 Write three types of analog-to-analog modulation and illustrate one…

A:

Q: Digital lab & design The circuits don’t have to be created in proteus project just a normal drawing…

A:

Q: Problem 3: Draw the small signal equivalent circuits of the circuits shown below: (a) (b) (c) R₂ R₁…

A: We need to draw small signal equivalent circuit for given bjt amplifier circuit .

Q: In the circuit below, BDC-BO-180 is given as VBE-0.7V. Find the Zib and ZO values accordingly. a) 5…

A: In the given questions we need to calculate the input and output Impedance of the amplifier.

Q: If you have (120 Vr.m.s and 60 Hz) signal design a circuit that produces the signal shown in the…

A: According to the question, If you have (120 Vr.m.s and 60 Hz) signal design a circuit that produces…

Q: What is non linear modulation?Explain with example?

A: Modulation: Modulation is the process of in which information from a message source is encoded to…

Q: 06) Consider the circuit shown in figure 5, assume that V Q6a) ID(en) (in mA) is: A) 0.02 B) 2 C)…

A: The circuit diagram is shown below, Where,RD = 4kΩandVZ =8 V

Q: A- By using graphical approach, find Ipo and Vcsą for the figure shown, where VDp = 9V, Rp = 3KN, Rp…

A: vgs=4.5v vg-vs=4.5 vs=0v vg=4.5v

Q: Table Q4(e) shows the reading obtain by a first order system with unit step input where c(t) is the…

A:

Q: Find the 2-Tras form of the sequeace and Ruc

A: Given sequence: xn=13nun+12nu-n-1

Q: Derive an expression for the Thevenin Equivalent voltage source of the 4-bit DAC. The source will be…

A: In given circuit four sorces are present i.e. b0,b1,b2,b3We need to determine the value of…

Q: For the circuit below, Why the output signal form appears as a square form? ? and why start from (-…

A: To answer above question, one should know what an amplifier is. An amplifier is an electronic…

Q: Which of the following standard is used to compare the limits of harmonic indices? ΙEEE 18 IEEE 519…

A: Given :    In the above question they have mentioned the different type of IEEE standards.   From…

Q: HW: Design a digital circuit for 1-to-4 Demultiplexer.

A:

Q: In the circuit shown below, find the base current IB if Ic = 301B. The base current is provided by a…

A: In this question We need to determine the base current IB  as shown the circuit.  Assume  VCE sat =…

Q: Causal signals an=n and bn = 2" are applied to a summation block. Write down the values of the first…

A:

Q: Q2): The N-bit DAC with an (R-2R) ladder network is to be designed as a 6-bit DAC device. Let (VREF=…

A: `

Q: Transform and draw the equivalent small signal circuit model using ONLY the HYBRID-PI model.

A:

Q: circuit design for AB' + AC' + AD' + BCD

A:

Q: Three-phase, 50 Hz 34500/10500 /Y connected transformer single-phase visible on the high voltage…

A:

Q: using c.D.R エ

A: rth is the open circuit impedance across the load

Q: a) Convert the following ( show all the steps): i. (1101 1100 1101 1101) 2 to ( ) 10 to ( )acp to (…

A: As per our policy, i have attempted one part. Convert the following i) Given number in binary form…

Q: Answer the following . Using PCM, encode the analog data below. Assume Vmax and Vmin as 5V and…

A:

Q: Discuss the Combinational Circuits

A: Combinational circuit : combinational circuit is circuit made of combination of various logic gate…

Q: Discuss the effect of increasing and decreasing proportional gain to the system output.

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: are shown in Rigure below TKe Signal x4) and gc4) Express x(4) n term f 34)

A: The solution is given below

Q: If the following data-input waveforms applied to the comparator, the *output in relation to the…

A:

Q: In Figure is given... Ys) 10 - R(O) O A) there are not correct answers B) multiple input and single…

A: In the block diagram input is one and out is many so it is a single input multiple output.

Digital to Analog Converters

Digital to analog converters are commonly known as DAC, digital analog converter, D2A, or Digital-to-Analog converters. DACs are one of the important devices used in the electronics and electrical domain. DACs are the systems that convert a digital signal into an analog signal, whereas an analog to digital converter or ADC performs the opposite function. Digital signals are those signals that can represent the information or data as a set of discrete values. At a particular instant of time, a digital signal can only take a particular value of data. A digital signal is characterized by two unique values; zeros and ones, or true and false, represented by the Boolean domain. These are also known as binary signals or logic signals. Unlike digital signals, an analog signal is represented by continuous values, where at any time instant, the analog signal is represented by a real number.