A feedback amplifier employing series-series feedback is shown in the figure below, where the feedback network is contained inside the dashed box. For the open loop amplifier, R₂ = 5kN, Gm = 100mS, and Ro = 1kn. The other component values are RA = 2ΚΩ, RB = 1kN, RS = 7kN. and RL = 6kn. Express your answers up to 3 decimal places.

A feedback amplifier employing series-series feedback is shown in the figure below, where the feedback network is contained inside the dashed box. For the open loop amplifier, R₂ = 5kN, Gm = 100mS, and Ro = 1kn. The other component values are RA = 2ΚΩ, RB = 1kN, RS = 7kN. and RL = 6kn. Express your answers up to 3 decimal places.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Plz solve both , i vll share positive feedback and vll upvote.... ASAP PLZZ
One advantage of having feedback in op amp circuit is A.Can control gain B.less complicated C.less input signal D.low gain E.high output voltage F.low bandwidth
Q-4. How many op-amps are required to implement this equation? V1+ R2 V. =- A) 3 B) 4 C) 2 D) 1 Q- 5. For the following feedback circuit. Identify the type of feedback and find the closed loop gain. E A ► VOUT
Q. One advantage of having feedback in op amp circuit is A. low gain B. low bandwidth C. can control gain D. high output voltage E. less input signal F. less complicated
a- Zero. b- Slightly different from zero. O Maximum positive or negative. d- An amplified sin wave. 9-Negative feedback reduces @ The feedback fraction. b- Distortion. c- The input offset voltage. d- The open-loop gain. 10-The input impedance of a current-voltage converter is Small. b- Large. c- Ideally zero. d- Ideally infinite. a- 11-In a linear op-amp circuit, the @ Signal are always sin wave. b- Op-amp does not go into saturation. c- Input impedance is ideally infinite. d- Gain-bandwidth product is constant.
1- Mention any two non linear applications of op- amp. 2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
Q3)Name, derive and determine the feedback and voltage gain, frequency of the figure below. Choose Q=15, and Q=6? Choose C1=10uf, C2=4uf, C3=8uf, L=27mH. +Vcc R1 R3 C5 out Amplifier R4 ll C3 Feedback circuit
QI. A siniscidal voltage waveform with 5 V pk-pk and period of 10 as is applied to the input of the op-amp shown in the figure. The open loop gain is 200000 and the supply voltage is +12 . Draw the input and output waveforms showing the time relationship. Vee
For the differential amplifier in Figure 6, find Ad, A and CMRR (in dB) where lo = 0.587 mA and Ro (current source) = 170 KQ. Suppose K = 1mA/v²
3ZJ The voltage at the node (between feedback resistance and in capacitor) of a differentaitor circuit is a.almost zero b.infinity c.approaching infinity d.maximum
1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
2-Discuss briefly the effect of both types of feedback on input and output impedance