A fan delivers 8.2 m3/s of air at static pressure 250 kPa when the speed of fan is 256 rpm and requires a power of 34 kW. If the fan speed is changed to 300 rpm, find the new air flow rate, static pressure and the power required.

A fan delivers 8.2 m3/s of air at static pressure 250 kPa when the speed of fan is 256 rpm and requires a power of 34 kW. If the fan speed is changed to 300 rpm, find the new air flow rate, static pressure and the power required.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shown below is the water jet flow from a pressurized closed tank. The vertical distance between free surface and the jet nozzle is . The vertical distance between the highest point of the water jet and the jet nozzle is . The flow is steady and no energy loss is involved. The acceleration due to gravity is . The water's specific gravity is . Find the velocity at point 2 ________ A. 17.2 m/s B. 16.0 m/s C. 255.05 m/s D. 294.3 m/s
The nozzle eff. Of a pelton turbine is 90%. Find the velocity of the water at the nozzle exit if the head is 180m
A hydraulic fork lift raises a mass of 8.9 ton at a speed of 0.5 m/s through a height of 13.5 mn once in 1.6 min, being working from an accumulator which is fed by a pump having an efficiency of 80%6. If the pressure of the water is 70 bar and the friction losses of the lift 30% find 1- The power required to drive the pump, 2- The minimum capacity of the accumulator.
Q2: Liquid water at 20°C flows straight up 30 m. 1- How much power pump is needed if the mass flow rate is 2 kg/s. take density of water 1000 kg/m3
1- A double jet of Pelton turbine driven by double nozzles to produce (4250 kw) to the shaft of an electrical generator when running at (400 rpm). The height of (180 m). wheel diameter is (1450 mm). The velocity of relative= 0.9 of jet velocity. If the angle of bucket is (165'), determine: a) Hydraulic efficiency b) Diameter of the jet
With a centrifugal pump directly connected to a diesel engine, 148 liters of water will be sucked 5 m deep and pumped 48 m high. The engine will be run at 1500 rpm. The total head loss in the suction pipe is 4 m.SS, the total head loss in the discharge pipe is 9 m.SS. Since the overall efficiency of the pump is 68%, find the power used by the pump. If the pump speed is reduced to 1200 RPM, what will be the flow rate and discharge head?
Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Que 4.35. A reaction turbine is revolving at a speed of 200 rpm and develops 5886 kW SP when working under a head of 200 m with an overall efficiency of 80 %. Determine unit speed, unit discharge and unit power. The speed ratio for the turbine is given as 0.48. Find the speed, discharge and power when this turbine is working under a head of 150 m.
As shown in the picture blew, a pump can deliver volume flow rate of of water through a vertical lift of . The inlet to the pump is just below the water surface and the discharge is to the atmosphere through a DN50 schedule 40 steel pipe. The energy loss . (4) Calculate power delivered by the pump in kW
3. An air compressor is to compress 8.6m³/min from 98.6kpa to 9860kpa. Assuming conditions ideal, with n=1.32. What will be the saving in work due to staging?
Note: Don't copy from other experts solution. If you don't know the solution please leave it but don't give me wrong solution. A 26-kW motor with 78% efficiency drives a centrifugal pum p delivery 68 L/s against a head of 24 m. Determine the pump efficiency.
A pump is used in a building to lift water from a ground floor. The pump is pushing 60l/sec of water through a 0.1m diameter to above floor which is 5m high. Calculate the velocity by which the water exits the pipe if water enters the pump at 30kPa and exists with 5kPa.