A factory engaged in the fabrication of an automobile part with a production capacity of 700,000 units per year is only operating at 62% of capacity due to unavailability of the necessary foreign currency to fiancé the importation of their raw materials. The annual income is P430,000, annual fixed costs are P190,000 and variable costs are PO.348 per unit. What is the breakeven point?

A factory engaged in the fabrication of an automobile part with a production capacity of 700,000 units per year is only operating at 62% of capacity due to unavailability of the necessary foreign currency to fiancé the importation of their raw materials. The annual income is P430,000, annual fixed costs are P190,000 and variable costs are PO.348 per unit. What is the breakeven point?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A contract to install and operate a rubber industries factory was referred to one of the companies and to market requirements« Asking to reduce the duration of the project What are the procedures adopted in the reduction?
The following assembly tasks (with performance time in minutes and task precedence) are to be configured into a balanced assembly line layout. There are 12 separate assembly elements (A-L) to complete the product. Note: The target is to produce 6 units per hour (60 min). please select more than 5 workstations in this problem as per the guidelines of the lecture note. Element (Min) Preceded Bv a) Construct the precedence diagram b) Determine the total work content time. A B C с D E F G H || J K L Time 2.5 4.5 3.5 4.0 3.2 2.0 2.7 7.0 6.0 3.8 5.0 4.3 A A A B B. C D D E F. G H I. J. K c) Use the "Longest Task Time" rule to assign work elements to stations (also known as "Largest Candidate Method". d) Calculate the efficiency of your solution. Complete previous Question using the "Ranked Positional Weight (RPW)" method to assign work elements to stations. Calculate the efficiency of your solution. Compare the performance of LTT and RPW in this case.
Your future company has purchased a machine and has entered into a contract that requires the company to pay $2000 each year for the upgrade of machine components at the end of years 6, 7, and 8. In anticipation of the upgrade cost, your company has decided to deposit equal amounts ( X ) at the end of each year for five years in a row in an account that pays i = 6% . The first deposit is made at the end of the first year. What is the value of X?
Question 4. Carbondale Casting produces cast bronze valves on a 10-person assembly line. On a recent day, 160 valves were produced during an 8-hour shift. a) Calculate the labour productivity of the line. b) John Goodale, the manager at Carbondale, changed the layout and was able to increase production to 180 units per 8-hour shift. What is the new labour productivity per labour-hour? c) What is the percentage of productivity increase?
The hourly cost of a hydraulic shovel is $80 and of a truck is $45. If an equipment fleet of 5 shovel and 8 trucks achieve a production rate of 220 BCM, what is the unit cost of loading and hauling, in cost per BCM.
The ABC company is considering constructing a plant to manufacture a proposed new product. The land costs P15,000,000, the building costs P30,000,000, the equipment costs P12,500,000, and P5,000,000 working capital is required. At the end of 12 years, the land can be sold for P25,000,000, the building for P12,000,000, the equipment forP250,000 and all of the working capital recovered. The annual disbursements for labor, materials, and all other expenses are estimated to cost P23,750,000. If the company requires a minimum return of 25%, what should be the minimum annual sales for 12 years to justify the investment?
(From Fundamentals of construction estimating book 4th edition ) 8.) If the output is expected to be on the high end of the scale, what would be the labor price to install 210 lb asphalt shingles based in Figure 12.5 data?
1- Most of ownership cash flows are expenses (outflow) but is cash inflow. 2- Major repairs & overhauls are included under because they result in an extension of a machine's service life. 3- The cost of lube oils, filters & grease will depend on the of company and conditions of work location. 4- The quantity of lubricants used an engine will vary with size of the engine, capacity of crankcase, the condition of piston rings, and 5- The scraper become uneconomical when the grades are greater than
А. Mrs. Goku is planning to have a new kitchen area with two sinks in her 25 square meter room. The height from the floor to sink is 1meter. What is your estimated number of fittings and valves for her kitchen and explain the offsetting of the pipes and the possible cost of overall project? Assuming that the price of following are: 1 meter/pipe is 250 pesos Pipefittings per piece = 15 pesos Valves per piece = 20 pesos Labor per day = 700
Engineers determined that a small amount of newly available chemical additives would increase the resistance of a building material by 20%. The factory manager arranged the purchase of the additive through a 5-year contract at a price of $7,000 annually, with an interest of 15% to be installed annually, and an inflation of 10%, starting from one year from now. The annual price is expected to increase by $50 annually starting from the sixth year and thereafter until the year 13. In addition, an initial investment of $3,000 has been made to prepare a suitable site for the contractor to deliver the additive. Find the equivalent total present value of all these cash flows.
I. LABOR COST 1. Brew Good Coffee produces and distributes whole bean coffee. Its facility employs 25 employees working on producing, packaging and delivering bags of coffee. Brew Good's owners want to calculate the hourly direct labor costs of its factory employees for the previous year. First, the owners determine the total expenses for the 25 employees by adding up wages, benefits and other contributions. The amount is 4,500,000, which represents total direct labor costs for the year. Next, the company adds up the number of hours the factory employees worked in the past year. Twenty employees worked 40 hours a week for 50 weeks. The other five employees worked 35 hours a week for 48 weeks of the year. What is the per-hour direct labor costs.
Case study scenario: A manufacturing company provides jobs for many people in a small town where employment is not easy to find. The company has stayed in the town even though it could find cheaper workers elsewhere, because workers are loyal to the company due to the jobs it provides. Over the years, the company has developed a reputation in the town for taking care of its employees and being a responsible corporate citizen. The manufacturing process used by the company produces a by-product that for years has flown into the town river. The by-product has been considered harmless but some people who live near the river have reported illnesses. Questions: What are the issues of integrity and ethics posed in the case study? What options does the company have, and what should it do and why?