A EI kNm kNm kNm 3 m 1 B 3 EI q kN/m 2EI 6 m C 4 m Click to see additional instructions Using cross method, determine the distribution factors for cross method (DF₁, DF₂, DFg and DF4) and internal bending moment at sections 1, 2, 3 and 4 (M₁, M₂, Mg and M4) in the frame? q 40 kN/m (If you find a negative value as your final answer, DON'T take absolute, write down the exact value with correct sign!! For end moments, define correct sign according to sign convention in DIAGRAMS!!) (Use "dot" for decimals and submit your answer with 2 digits) DF, = DF₂= DFg DF M₁ M₂= M₂ =

A EI kNm kNm kNm 3 m 1 B 3 EI q kN/m 2EI 6 m C 4 m Click to see additional instructions Using cross method, determine the distribution factors for cross method (DF₁, DF₂, DFg and DF4) and internal bending moment at sections 1, 2, 3 and 4 (M₁, M₂, Mg and M4) in the frame? q 40 kN/m (If you find a negative value as your final answer, DON'T take absolute, write down the exact value with correct sign!! For end moments, define correct sign according to sign convention in DIAGRAMS!!) (Use "dot" for decimals and submit your answer with 2 digits) DF, = DF₂= DFg DF M₁ M₂= M₂ =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(b) Setup the equations to determine the member end moments of the following beam using the slope deflection method (no need to find the final answers)< EI= constant 2 A 2m 20KN 2m B 5kN/m 4m 2m 10 kN/m 3m D 1
Q3. Analyse the member end moments and reactions for the continuous beam shown below using the slope deflection method. E = 200GPA 1 = 7x10° mm. 60KN 15KN/m 10m 5m 5m D.
Please help me solve this question
From the given beam loaded has shown; Determine the deflection at point D in mm. Using Moment Area Method. Let P =37 kN. EI = 14220kNm2 | 2P D B A - 2P 3.0 m 1.5 m 1.5 m Moment diagram by Parts 3P -3P Deflection curve diagram
PROVIDE COMPLETE SOLUTION FOR ME TO FOLLOW
2. The box beam is made of elastic perfectly plastic material for which sY = 250 MPa. Determine shape factor of the section (hint: Mp=289062.5 N-m) 25 mm 25 mm 150 mm 25 mm 150 mm 25 mm
Given the propped beam with an internal hinge as shown in the figure, what is the maximum safe value of w (in kN/m) if the absolute maximum shear produced is 70 kN? (input a positive value only) Hint: RA = RD and Rg = 8.25w (kN). %3D Use equations instead of diagrams. w(KN /m) A qm BO4SM 4,5M OD internal hinge
structural analysis theory of indeterminate beam. using Slope-Deflection Method 2) Using SDM, analyze the continuous beam below and draw the shear and moment diagrams. 4m 10 kN/m 10 kN/m 15KN/m 30 kN/m In 2 =0.8 I I3 = 0.8 I1 D A B 8m 8m 6m 2m Note: There are no SDE's for cantilever ends.
Please answer asap Use Slope deflection method Than you I will rate
need fast comp. Values should be in 3 decimal places
Hi . See example qno2 . Need like this for 7. U can answer any question with solutions diagrams. No searchable Dont reject my question
The simply supported beam AD is subject to a uniform load over the segment BC together with a |12 kN 10 kN/m concentrated force applied at C as shown in Figure. B. Using singularity functions, write equations for the to shearing force and bending moment at any point in 2,5 m 1 m Im R. the beam and plot shear and moment diagrams.