A drone will be used for a rescue mission. As an engineer, you are requested to choose the most suitable drone for the operation. The aim is to arrive at the exact location as fast as possible. The altitude position responses of three drones (4, B, C) to a unit step input is shown in Figure Q.1. Based on the responses, select the best drone to perform the mission. Provide reasons for the selection by comparing with other drones. Also describe the disadvantage of the selected drone. 1.4 1.2 Step Response 0.8 0.6 C 0.4 0.2 2.5 5 7.5 10 12.5 15 Time (seconds) Altitude position

A drone will be used for a rescue mission. As an engineer, you are requested to choose the most suitable drone for the operation. The aim is to arrive at the exact location as fast as possible. The altitude position responses of three drones (4, B, C) to a unit step input is shown in Figure Q.1. Based on the responses, select the best drone to perform the mission. Provide reasons for the selection by comparing with other drones. Also describe the disadvantage of the selected drone. 1.4 1.2 Step Response 0.8 0.6 C 0.4 0.2 2.5 5 7.5 10 12.5 15 Time (seconds) Altitude position

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are four primary way to move drone of hexacopter by using controller??
A 480V, 120KVA, 50HZ, 4-pole, Y-connected SG was tested to get VToc=500Vand Isc=180A at rated field current and Ide=50A at Vde=25V. If the machine is operating at rated conditions and PF=0.92 lagging. wwwm 1. Find Armature Resistance (RA) and Synchronous Reactance (X) 2. Calculate the armature current, and the internal induced voltage EA. 3. Find the full load Voltage Regulation.
1
3. A factory's separately excited DC generator has an armature resistance of 0.252. The machine is driven at 1000 revolutions per minute giving the following data: E,[V] I[A] a) Plot the open circuit characteristic when the machine is driven at 1000 and at 1500 rev/min. b) If the machine is drive at 1500 rev/min and its field current is adjusted to 0.2 A, plot the output voltage (in the same axis with (a)) as the load current is varied from 0 to 40A. For a full load current of 40A, what is the voltage regulation? 5 28 75 112 132 150 0.1 0.3 0.5 0.7 0.9
The preferred method for applying the field excitation voltage uses a field relay which operates on the principle of A. speed application. B. time application.C. angle application. D. thermal application.
It is aimed to implement an automatic test system to be used in a laboratory environment in order to perform comprehensive functional tests to be used in the development and verification stages of an avionic control unit. To meet below needs, a programmable/automatic test equipment/system is required. REQUIREMENTS OF THE PRODUCT TO BE TESTED The features expected from the test system (TS) to be designed are listed below: V TS will be able to supply 28Vdc 5A power to the Product to be Tested. V TS must be able to separately read 2 analog output signals coming from the Product to be Tested. The output characteristics of the analog channels of the Product to be Tested are described below: • 3.3V Amplitude • 1.65V Offset • 250kHz sine wave V TS will be able to operate by generating pulse or continuous square wave signals to 8 digital inputs of the Product to be Tested. The amplitude voltage level is 12V. The smallest pulse width duration is 1 ms. V TS will be able to send messages over the…
- What are ultrasonic sensors in electrical engineering?
Make a drawing/design of a block diagram of a synchronous sequential machine with its parts labelled. List the procedures used to draw/design the synchronous sequential machine.
In the control system below, calculate the necessary control poles and PD controller parameters (Kp and KD) so that the settling time can be Ts=2 sec, maximum overshoot Mp= 0.05 (5%) according to the 5% criterion.
Answer with Proper explanation?
Techniques used to calculate stability 2. Discussed briefly the effects of the different types of compensators in control systems.
Explain the construction and operation of instrument whose deflecting torque is proportional to the square of operating quantity. Also draw the instrument with labelling.