A drect-drive crawler tractor with a rated blade capacity of 12 LCY is being used to exchange the location of 2 different stockpiles by pushing the material from one stockpileto the other. The first stockple consists of loose common earth and the second stockpile is hard clay. The distance between Stockpile 1 and Stockpile 2 is 250 ft. Estimate theproduction of the dozer if the job efficiency is 50 min/h,

soil moving from loose common earth to hard clay and also the data to find out production is…

A drect-drive crawler tractor with a rated blade capacity of 12 LCY is being used to exchange the location of 2 difterent stockpiles by pushing the material from one stockpile to the other. The first stockpile consists of loose common earth and the second stockpile is hard clay. The distance between Stockpile 1 and Stockpile 2 is 250 ft. Estimate the production of the dozer if the job efficiency is 50 min/h,

A drect-drive crawler tractor with a rated blade capacity of 12 LCY is being used to exchange the location of 2 difterent stockpiles by pushing the material from one stockpile to the other. The first stockpile consists of loose common earth and the second stockpile is hard clay. The distance between Stockpile 1 and Stockpile 2 is 250 ft. Estimate the production of the dozer if the job efficiency is 50 min/h,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Transportation and moving How many 5-ton LCY dump trucks will it take to support a wheel loader having a 1.5-cubic yard heaped- bucket capacity. The haul-unit cycle time is 30 minutes excluding loading time. The loader cycle time per bucket load is 0.5 minutes. Consider a 45-minute working hour. 2. Compaction a) What is the estimated production rate (CCY per hour) for a smooth-drum vibratory with a compaction width of 4 feet? The following information was obtained from a test strip at the project: Compacted lift thickness = 3 inches Average speed = 5 mph Number of passes = 8 Efficiency Factor = 0.83
____________means drilling in known productive portions of the reservoir that have not been properly drained and is usually done later in the life of the reservoir. a. Wildcat well b. Infill well c. Exploratory well d. Appraisal well
Data on a simple summit mass diagram: STA 0 +000 Mass Ordinate (cu. m.) -80 0 + 500 -130 Initial point of limit of freehaul distance = +600 Initial limit of economic haul = +200 Freehaul distance = 60m Limit of economical distance = 400 m Cost of haul = P120 per cu.m per meter station. Draw the diagram, and determine the volume of waste in cu.m.
assume all structures are composed of frame elements (beams and columns), i.e. internal shear, bending, and axial force may be present. Determine: ns , nsE, nsl, and whether the structure is stable or unstable. For ns, show your work for both the equation method and the "by inspection method" showing interim structures as releases are made. 2. TTTTT
QI:- Design a settling tank for a flow of 0.2 MGD if the overflow rate is not to exceed 600 gpd/n. Calculate dimensions if the tank is circular with a depth of 12 ft. Calculate dimensions if the tank is rectangular with a depth of 10 fit and a length to width ratio of 4 to 1 Q2:- The settling velocity of alum floc is approximately 0.0014 f/s in water at 10 C. Calculate the cquivalent overflow rate in gpd/f12. What is the minimum detention time in hours to settle out alum floc in an ideal basin with a depth of 10 ft? Q3:- Two rectangular clarifiers, cach 30 ft long, 15 ft wide, settle 0.40 MGD following alum coagulation. The effluent channels have a total weir length of 60 ft. Calculate the detention time, horizontal velocity, rate of flow over the outlet weir. Do these values meet the GLUMRB Standards for water works? Q4:- Calculate the diameter and depth of a circular sedimentation basin for a design flow of 3800 m3/d based on an overflow rate of 0.00024 m's and a detention time of 3…
03:- Given the stratified soil system shown in Fig. Requie what is the head dvop is the corresponding Plow through a unit area of soil? across each stratum and what Ki H2-2 プ
Propose a commercially available pump which may be used in the case of extremely abrasive and corrosive slurries. Its performance curve must be shown.
A 6-m self-propelled combine makes an average stop of 5 minutes everytime its 3-ton grain tank is to be unloaded. The yield of the 30-ha field is 60 tons. The operating speed is 6 kph. The time for turning on the headland at the ends of the 500-m field is 20 seconds. Find: a. theoretical field capacity b. actual field capacity c. Field efficiency
Two scrapers will deliver to the project 650 LCM per hour of fill material. The rolling width of the roller is 1.2m. 6 passes at 4 km/hr are required to obtain the required density. The fill material will be placed in 0.3m compacted lifts. Load factor (LF) = 0.8 and shrinkage factor = 0.85. Assume a 50-min job efficiency, determine the number of rollers required to support the scraper operation.
MOO 1贪l Mid-1st cours... Engineering Geology Mid. Ist Course Exam Dr.Oasim Al-Obaidi 16.3.2021 01: Fill the blanks with suitable words: 1. Clay mineral rype Kaolinite have Gibbsite: Silicate mineral structure of a.l: h.2:1 c.2:2 d.1:2 2. Laterites soils is .. a. Residual ........ C. sand d. None of them b. Transported 3. Glaciers or their meltwaters transported sediment such as . b. water d. Non of them a. Till 4. The hydration processes of rocks can transform the Anhydrite (CaSO4) to. a. Sodium chloride C. Alluvium b. Gypsum c. Potassium Carbonate d. Clay Minerals .......-----weathering is the activities of organisens, including plants, burrowing animals and humans. a. Chemical d. Non of them b. Biological 6. Material moved downhill by gravity is called... b Сolluvium c. Physical a. Alluvium c. glacial drift d. Loess 7.. .is solid with very high density materials with an average density 17 gm/cm'. . a. Outer core b. Mantel c. Inner core d. Crest 8. The outer solid earth envelope up to…
A load of hematite has a density of 5.3 g/cm3. If the mass of the load is 150 metric tons, how many dump trucks, each with a capacity of 15 cubic yards, will be needed to haul the whole load. Assume that the truck(s) can carry the load from the mine to the dumping zone only once. 1 m = 1.09361 yd
assume all structures are composed of frame elements (beams and columns), i.e. internal shear, bending, and axial force may be present. Determine: ns , nsE, nsl, and whether the structure is stable or unstable. For ns, show your work for both the equation method and the "by inspection method" showing interim structures as releases are made. 5. TTTTT