A double riveted lap joint is made between 15mm thick plates. The rivet diameter and pitch are 25 mm and 75 mm, respectively. If the ultimate stresses are 400 MPa in tension, 320 MPa in shear and 640 MPa in crushing, find the minimum force per pitch which will rupture the joint. If the above joint is subjected to a load such that the factor of safety is 4, find out the actual stresses developed in the plates and rivets.

A double riveted lap joint is made between 15mm thick plates. The rivet diameter and pitch are 25 mm and 75 mm, respectively. If the ultimate stresses are 400 MPa in tension, 320 MPa in shear and 640 MPa in crushing, find the minimum force per pitch which will rupture the joint. If the above joint is subjected to a load such that the factor of safety is 4, find out the actual stresses developed in the plates and rivets.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two plates 50 mm wide and 20 mm thick are lap jointed by a 20-mm dia. pin and loaded with 75 kN tensile force. Estimate shear stress on the pin in MPa.
Figure 2.1. shows two long plates with same material and equal width w=20 mm that are subjected to a uniaxial tensile load o. One of the plates has a single small central hole with diameter 4mm and another plate has two small holes with a distance of 8mm from each other. The holes are perpendicular to the external tensile load. Develop a computer code (or simulation model) and analyze how stresses will be distributed at the tip of the holes in these two plates for different values of 0. 4mm Figure 2.1. 8mm 4mm
A metal tube with inside diameter of 100mm is subjected to a tensile lad of 500kN. Find the outside diameter if the ultimate tensile stress is 600MPa and a factor of safety is 5.
Two links are connected by a single pin and a tensile force F is applied. The links and the pin are made from Aluminum(sigma_y = 35ksi and T_y = 20ksi). The dimension of the link is 5 inch high by 0.5 inch thick. Find the optimal diameter for the pin and the maximum force,F that can be applied to the linkage before incuring permanent deformation.
A bar of 12 mm diameter gets stretched by 3mm under a steady load of 8000 N. What stress would be produced in the bar by a weight of 800 N which falls through 8 cm before commencing the stretching of the bar which is initially unstressed. Take E= 2 × 105 N/mm2
A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch a hole in a 1/4 in. plate. If a force P=20,000 lb is required, what is the average shear stress in the plate and the average compressive stress in the punch?
Two plates are held together by 4, 28 mm diameter bolts. If a 25 kN load is applied to the plates in shear, what is the shear stress in the bolts in MPa?
A steel rod on a bridge must be made to withstand a pull of 6000 Ibs. Find the diameter of the rod in mm. assuming a factor of safety of 7 and ultimate stress of 62,000 psi (round off to whole number).
Calculate the axial stress in a tube that is stretched by a tensile axial force of 4500 N if the tube has an outer diameter of 25 mm and an inner diameter of 20 mm.
In the attached picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 500 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?