A discrete time linear shift-invariant system has an impulse response h(n) withh(0)=1, h(1)=-1, h(2)=2 and zero otherwise. The system is given an inputsequence x(n) with x(0)=x(2)=1, and zero otherwise. The number of nonzerosamples in the output sequence y[n], and the value of y(2) are, respectivelyonSelect one:6, 15.3.6.ADE dE ING Abood Khreisatكان نشظا منذ ۱ ۱ دقيقةLet P be linearity. Q be time invariance, R be causality and S be stability A discrete time system hasthe input output relationship yin)-05(n) +x(nluln 1)+ xin-1ju(1-n) Where x(n) is the input and yin) is the output. Theabove system has the properties.Marked out of2.00Select one:OA POS but not RD.PS but not QROCQRS but not POa PORSC haicePrevious pageNext page•..المزيدتعديل

A discrete time linear shift-invariant system has an impulse response h(n) with h(0)=1, h(1)=-1, h(2)-2 and zero otherwise. The system is given an input sequence x(n) with x(0)-x(2)-1, and zero otherwise. The number of nonzero samples in the output sequence y[n), and the value of y(2) are, respectively Select one 6. 1 5. 6. 2. 5. ADOANIN 3.

A discrete time linear shift-invariant system has an impulse response h(n) with h(0)=1, h(1)=-1, h(2)-2 and zero otherwise. The system is given an input sequence x(n) with x(0)-x(2)-1, and zero otherwise. The number of nonzero samples in the output sequence y[n), and the value of y(2) are, respectively Select one 6. 1 5. 6. 2. 5. ADOANIN 3.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the system given constant coefficient difference equation: yInl-2.5yIn-1]+yIn-2]=2x[n]+0.5x[n-1] a) Define the region of convergence to obtain a stable system. b) To get causal system, define the region of convergence and find the impulse response. c) Provide information about the action that can be taken to causally and stabilize the system.
x(t) 3 2 1 Figure 1(a) 2 t
The signals x(n) and y(n) shown in figure are the input and corresponding output ofan LTI system.- Find the response of the system to the sequence x2(n) shown in the figure.- Find the impulse response of the LTI system.
Q2)a)Given x(t) and the impulse h1(t) as below find and draw y(t) h1(t X(t 1 1 1 -1 b)for the same system in a if the impulse response of the system is given as h(t) = > h1(t – 2m) m=-00 For the same input find and draw y(t) c)find the total energy and power of the following signal X(t) 1 -5 -4 4
Lecture is Signals and Systems. Could you solve this for me
4. Solve for the zero-input, zero-state responses, and the total response of the system shown below. The initial conditions are given as y(-1) = 1 and y(-2) = 1, and x(n) = 3u(n). x(n) (n)
Length of the linear convolution output y[n] is 400 and length of the impulse response h[n] is 40. Then the length of the input sequence x[n] assuming that the length of linear convolution output is reduced by 50% is.
I need the answer as soon as possible
Problem 1e) should say (ignore the part about complex-conjugate poles/zeros ) : Setup the equation to determine breakaway/break-in points of the root locus
Exercise 2: 1- Precise the features of the Infinite Impulse Response (IIR) 2- Explain the process of the Bilinear Transform Design
1.) Given the input signal and impulse response, find the output signal by evaluating the convolution integral directly. DO NOT use any special formulas or identities. x(t) = u(t) h(t) = sinnt [u(t)-u(t-1)]
For the following system, if the input X[k]= 8(k+ 1) +2.4* and output Y[k]=2(k)u[k], the impulse response is h[k]- A.k. 2u[k] + B. (k-1). 2-1).u[k-1], so the values of A. B are............. X[k] O a. 3,1 O b. 3,-1 C. 0.5, -2 O d. 5,-2 Oe. None of them H(z) Y[k]