A digital combination lock takes a serial input (S). If the correct signal sequence of "101" is received, then the door is unlocked and opened. Once the door has been opened, the lock (L) is reset. If the wrong sequence is received then the lock is reset. A sequential logic circuit can be used to implement the digital combination lock using flip flops. (a) Complete a state transition table for the circuit described above, to show the cur- rent/next states/output for each possible combination of states and input. The table structure you should use is shown below:

A digital combination lock takes a serial input (S). If the correct signal sequence of "101" is received, then the door is unlocked and opened. Once the door has been opened, the lock (L) is reset. If the wrong sequence is received then the lock is reset. A sequential logic circuit can be used to implement the digital combination lock using flip flops. (a) Complete a state transition table for the circuit described above, to show the cur- rent/next states/output for each possible combination of states and input. The table structure you should use is shown below:

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Part a Design a logic circuit using the truth table Inputs output shown. Use only basic logic gates (AND, OR, NOT). Also, the circuit should use the FEWEST number of gates and the FEWEST number of inputs to the gates. Fully label all the inputs and outputs. a b. 1 1 1 1 1. 1 1 Part b Implement a 3-input XOR gate using only a 4x1 multiplexer and an inverter. Also complete the truth table in your answer sheets with the correct labels and function solution. Fully label all inputs and outputs. Part c Design a full-adder using half-adders and A- additional logic using the half-adder shown here. Pi Gi
Don't copy
Design a three-input combinational logic circuit for F(A,B,C)= )7,6,4,2,0(m. Simplify the output expression of F. You may choose to use either Boolean algebraor Karnaugh map techniques to simplify the design. Finally, implement the design circuit from the final output expression of Fusing only AND, OR and NOT logic gates.
2. Consider the circuit below. a. Write the Boolean expression for output F in terms of A, B and C. b. Construct a truth table for the circuit with A as MSB and C as LSB. c. Write the Canonical SOP and POS forms for output F. A B C 3. Draw the logic circuit represented by the expression F(A, B) = AB using no more than 5 units of 2-input NAND gate and write the corresponding Boolean expression.
Universal Gates Exercise: Redraw the below logic diagram. The new circuit have to consist of AND and OR symbols. Develop the output expression for the new circuit. A G3 B G2 G1 D G5 E G4 F.
Question 2: A combinational circuit has 4 inputs (A, B, C, D) and 1 output (F). ABCD represent a majority function. The output of the majority function is equal to 1 if the input variables have more 1's than O's, otherwise the output is 0. a. Construct the truth table of the required circuit. b. Implement the minimized expression of F using 3-level all NAND gate circuit. Implement a 2-1Multiplexer using three-state buffers.
Q5// Design a combinational .logic circuit that has 4-inputs (A,B,C,D) and one-output (F), the output will be high "1" when the majority of inputs are high"1", and then simplify the output use POS expression in K-map and draw logic circuit.
The test .. is active when using Boolean difference technique in the logic circuit that illustrated below * .with fault is C6/1 C3 X1 C5 C4 X2 C7 F C2 C6 C1 t3 t0 t2 and t3 t0 and t1 O
la. Draw the truth table for the following set of gates with inputs A, B, C and D and result R: NOT - A OR AND - B R OR NOT -C - -D - b. Use the truth table to generate a Booleanexpression describing the function (using minterms))
Q1. Design a logic circuit that perform. the gray code on the 4-input binary weighted code 2421 using Karnugh Map (K.M) implementation method? Using Electronic Workbench. i.e. weighted code 2421 Gray code
Task 4: Simplifying Boolean functions Simplify the following Boolean expression F (A, B, C) = (A+C") +C (C.A' + (B.A) +C Draw the simplified Boolean expression using EWB. Find out the truth table of the circuit.
PROBLEM: Given the Logic expression X = [(A+B) + (CC) ] [(CC) + (BOD)] (a.) Draw the Logic circuit and write the OUTPUT of EACH gate in a given table below. (b.) Connect the Logic Circuit in the TINKERCADD that you have drawn and write the output in a given table below. TRUTH TABLE: A B C D 0 0 0 0 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0 0 1 0 1 0 1 1 0 0 1 1 1 0 0 0 1 0 1 1 1 0 1 1 1 1 0 0 1 0 1 1 1 0 1 1 1 0000 0 0 1 1 1 1