A diesel electric power plant supplies energy for Meralco. During a 24-hour period, the plant consumed 240 gallons of fuel at 28°C and produced 3930 kW-hr. Industrial fuel used is 28°API and was purchased at P30 per liter at 15.6°C. What is the cost of fuel to produce one kW-hr?

Q: Explain the reasons why the Diesel station is superior to the thermal power station? mention it?

A: Given Diesel station To find Advantage of diesel engine over thermal power plant station

Q: Find the Mass of natural gas in Kg/min of a Gas turbine power plant operates on simple Brayton cycle…

A: GivenNet power=112.464Mwco2 emissions=900G/kwh=0.9kgkwhassumptions η=0.31

Q: Why is humans are very dependent on the used of fuels to produce power?

A: Alternative fuels reduce toxic exhaust emissions (such as carbon dioxide, carbon monoxide,…

Q: The generato efficiency of a diesel fuel power plant is 98% with engine generator rating of 0.212…

A:

Q: P a Pa P,/2 b 2V.

A: For solution refer below images.

Q: Q2. Thermal power station contains three units, one 700kw and two units with 500kw for cach one. The…

A:

Q: Water vapor at 20000kg /hour  flows into a steam boiler with a specific volume of 225 kPa 0.7565 m ^…

A: Write the given information.

Q: b) Explain using sketches how a combined cycle power plant might operate. What cycles are involved…

A: Combined cycle power plant as in name suggests, it combines existing gas and steam technologies into…

Q: Many batteries in cellphones and new hybrid cars have what element as energy source

A: Given Data : Batteries Cellphones New hybrid cars

Q: 2. Draw and Explain Schematic diagram of Geo Thermal power plant. Discuss its advantages.

A:

Q: A diesel power plant uses fuel with heating value of 45,325 kJ/kg. What is the density of the fuel…

A: Heating value, Q= 45325 kJ/kg T= 40∘C   To find: Density of the fuel at 40∘C, ρat 40∘C   Note:…

Q: The owner of a propose steam power plant received bids from two fuel supplier. The first supplier…

A: Given data: Net power output = 100 MW Turbine inlet enthalpy h1 = 3582.3 kJ/kg Turbine outlet…

Q: Give PV and TS Diagrams of Actual Bryton Cycles. Give also the Work and efficiency equation

A:

Q: Consider a diesel electric plant which consumes a thousand liters of fuel with 20 oAPI at 200K in a…

A: GivenV=1000ltr= 10001000m3=1m3APIo=20otime =1day=24×60=1440 min

Q: H1. A stack gas containing 71.9% N2, 10% CO2 and 18.1% CO is passed through a turbine. This gas…

A: stack gas containing 71.9% N2, 10% CO2 and 18.1% CO. Temperature = 760o F P= 0.5 in H2O coal…

Q: 2.In a regenerative steam cycle, steam enters the turbine at 7.2 Mpa and 510°C. Steam is extracted…

A: GIVEN DATA - A REGENRATIVE RANKINE CYCLE GIVEN WE HAVE TO FIND ALL THREE GIVEN POINT

Q: ow you will integrate the wind, solar, Biogas. Explain with neat diagram of an integrated Hybrid…

A:

Q: ESuperheuted steam at 350 and 20 bar enters the turbine of steam power plant and expands to a…

A:

Q: If heat rate is 12x10° kJ/kWh, then efficiency in percentage will be equal to

A:

Q: 010. Sketch a P-V diagram Carnot cycle for a heat pump. What does the area enclosed by the graph…

A: The p-v diagram is shown where the area enclosed represents the work done.

Q: The figure below shows a vapor power cycle that provides process heat and produces power. The steam…

A:

Q: Enthalpy data is given for a regenerative Brayton cycle with intercooling and reheating. The cycle…

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: thermal efficiency =

A: Need to find thermal efficiency

Q: A powerplant operates according to the ideal Rankine cycle shown in the figure. Reheat and…

A:

Q: create a diagram of the geothermal energy flow in a geothermal power plant.

A: Draw the block diagram of the geothermal energy flow in a geothermal power plant

Q: Q1/ A power plant operating on Carnot cycle that produces (500MW). It turned out that this…

A:

Q: 60 MW new combined power plant typically consists of: wo steam turbines (20MW each) and one gas…

A: Given: The power of combined power cycle, W = 60 MW

Q: Q5. Choose the correct answer for each of the following: 1- The efficiency of the Otto cycle is…

A:

Q: Consider a diesel electric plant which consumes a thousand liters of fuel with 20 degree API at 200K…

A: Given data: V˙=1000 L/day Need to determine the fuel rate in kg/min.

Q: A 330 MW steam power plant operates according to the simple ideal Rankine cycle. water vapor enters…

A:

Q: If you are the engineer or consultant of a company and the owner ask your opinion to what type of…

A: Powerplants are large industrial facilities developed for the generation of electricity through…

Q: A diesel power plant use fuel with HHV of 45000 kJ/kg. What is the density of fuel at 25 deg. C?

A:

Q: A combustion chamber in a Gas Turbine Power Plant has efficiency equal to 62.82%, What is the actual…

A:

Q: Q2_It is desirable to calculate the power of a diesel for a building with a power consumption of 200…

A: Given   Power, P = 200 kW  Power factor for diesel engine = 0.74 Find  Power of a diesel engine in…

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.