A diatomic gas engine contracts isothermally from V2 = 2.00 m³ and p2 = 172 kPa to a volume V₁ and pressure 574 kPa. The engine then follows an isobaric process to V2, then an isochoric process to the original pressure, p2. Calculate the engine's efficiency. [Hint: Start by drawing the engine cycle on a pV-diagram.] .1152

A diatomic gas engine contracts isothermally from V2 = 2.00 m³ and p2 = 172 kPa to a volume V₁ and pressure 574 kPa. The engine then follows an isobaric process to V2, then an isochoric process to the original pressure, p2. Calculate the engine's efficiency. [Hint: Start by drawing the engine cycle on a pV-diagram.] .1152

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider an air-standard Diesel cycle. Operating data at principal states in the cycle are given in the table below. The states are numbered as in the figure below. State T(K) p (kPa) u (kJ/kg) h (kJ/kg) 380 100 271.5 380.6 1096 5194 841.9 1157 3 1864 5194 1546 2081 4 874.6 230.1 653.1 904.1 b. Determine: (a) the cutoff ratio. (b) the heat addition per unit mass, in kJ/kg. (c) the net work per unit mass, in kJ/kg. (d) the percent thermal efficiency.
Answer the Following problem. Show complete solutions and please write legibly. ty *not a graded questions *review purposes only
Thermodynamics subject power cycles. Show the ts diagram and complete and step by step solution. Box the final answer.
010. Sketch a P-V diagram Carnot cycle for a heat pump. What does the area enclosed by the graph represent?
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the firstturbine until it is just dry saturated, then it is re-heated to 400 °C and expandedthroughthe second-stage turbine. The condenser pressure is 0.04 bar what is the pressure in bar at state 4 to 3 decimal places? what is the specific entropy in kJ/kg-K for state 5 to 4 d.p.?
Q3: A distillation column is separating acetone(more volatile component) from ethanol. As pictured, there are two feeds with flow rates F₁=100 mol/hr and F₂-200 mol/hr. Feed 1 has z₁-0.7 and is saturated liquid. Feed 2 has z2 0.4 and is a superheated vapor (q=-0.1) where approximately 1 mol of liquid will vaporize on feed stage for each 10 mol of feed. We desired xd-0.95 and xw-0.05. How many stages are needed to achieve this separation? Ln/Vn=0.64.
You are working as an assistant to a physics professor. She has seen some presentations you have made to your classes and is aware of your expertise in preparing presentation slides. Her laptop has crashed and she cannot access the presentation slides she needs for her lecture coming up in one hour. Her lecture is on entropy in engine cycles. She asks you to quickly generate two slides on your laptop, both showing TS diagrams, (a) one for the Carnot cycle and (b) one for the Otto cycle. As she leaves, you think, “Uh-oh. What’s a TS diagram?” Quick, you have no time to waste! Get to work!
Letter C, D and E
12.) Water at a rate of 1 lbm/s flows in a vertical heated tube (d = 1.5 in). Systempressure is 1250 psia. Find heat flux at a point where steam quality is 15% andsurface superheat is 12 F. [Ans.: q′′ = 108 kW/m2]
Having difficulty with this engineering problem. At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.1 L. Determine per cylinder: a) the volume at state 1 in L.b) the air mass per cycle.c) the heat addition per cycle, in kJ.d) the heat rejection per cycle, in kJ.e) the net work per cycle, in kJ.f) the thermal efficiency.g) the mean effective pressure, in bar.h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar.i) Devise and evaluate the exergetic efficiency for the cycle.
Show the ts diagram and complete and step by step solution. Thermodynamics subject.
I need correct answer in 20 minutes please Find the cycle efficiency and specific steam consumption of a reheat cycle (Fig. 2.7a) operating between pressures of 3 MPa and 0.004 MPa, with superheat temp of 450 °C. Assume that the first expansion is carried out to the point where the steam is dry saturated and then the steam is reheated to the original superheat temp. The feed pump term may be neglected Boiler Reheater a High-P turbine. P = Ps= Preheal Pump Condenser Low-P turbine Figure (2.7 a) High-pressure turbine Reheating Low-pressure turbine