(a) Determine the value of the voltage VO for Vi = 5 [V]. Obtain the currents and voltages for each diode. b) Determine the value of the voltage VO for Vi= 12 [V]. Obtain the currents and voltages for each diode. Complete the table Diode D1 D2 D3 202 Voltage (V) +10 V D1 Vi = 5V Current (A) D2 +10 V {20 20 -10 V VO (V) D3 Voltage(V) Vi = 12V Current (A) vo (V)

(a) Determine the value of the voltage VO for Vi = 5 [V]. Obtain the currents and voltages for each diode. b) Determine the value of the voltage VO for Vi= 12 [V]. Obtain the currents and voltages for each diode. Complete the table Diode D1 D2 D3 202 Voltage (V) +10 V D1 Vi = 5V Current (A) D2 +10 V {20 20 -10 V VO (V) D3 Voltage(V) Vi = 12V Current (A) vo (V)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Using the ideal diode model, find the output voltage for the input voltage of the following circuit and graph it in detail. (a) (b) R₁ D₁ www ww R3 D2 (a) R₁ D₁ www + + D2 R2 vo Vo R₂ (b)
1. Determine Vpout for the circuit in below and draw Vauts assume the diode is the silicon type. 10 k +10 V-- V. ov R, 100 k IN914 -10 V- 2. What is the output voltage that you would expect to observe across R, circuit of Figure below? Assume that RC is large enough to prevent significant capacitor discharge. +24 V 10 uF RL 10 kn V. ov. IN914 -24 V
Assuming ideal diode the voltage across the resistor R2 in the circuit shown in the Figure is: R1 E = +12V0- 2.2k2 RE1.8kN E, = +4V A 4.0 V 7.6 V 3.6 V D 4.4 V
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. R1 ww 9kQ 1N1199C R2 D1 18kQ 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 D3: On (Forward Bais) D3: Off (Reverse Bais)
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Consider diode circuit shown below with Vcc=5V and V₂ = 3V. U₁A HH +V₂ ū The peak inverse voltage on the diode is close to V₁ V. A Vo
3-) In the circuit below, find the input voltage range that must be used for the zener diode to be in continuous transmission. (Vz=LOV, Izm = 40mA) Rx 2k ZVz RY 2k Jo
5V 3000 1000 . 2m 1 Si 4000 500 12V The circuit shown in Figure 1 contains a Si diode with a diode resistance on 1000. Use the piecewise linear model to solve the circuit. • How many nodes are in the circuit? • Determine the Thevenin voltage across the diode. Replace the diode with the appropriate model and then solve the circuit to determine the power dissipated by each resistor and the diode.
B. For the circuit shown below, assume that the zener diode has Vz-3.3V and rz=092 when reverse biased, and has a 0.7V drop when forward biased. Fill the following table for values of Vo for different values of input voltage Vi. R1 Vi Vi -8V OV 8V 1k 5V N V2 R21k Vo Vo
what is the voltage across the diode? what is the current through the diode? what is the current through the 100 ohm in series with the 3V? what is the current through the 5V line?
You are told that the approximate diode knee voltage is 750mV, but you need to know for sure. You are told that the diode's saturation current is I, = 2.27fA. (2.27x10-15 A) and V=25mV. Determine VD. Iterate until you have the answer to 2 significant figures.
Assuming an ideal diode model for all the diodes in the circuit below, Calculate the voltage across and current flow through each diode 9kO 1N1199C R2 01 18kO IN1199C V2 12 V- R3 1kO D3 1N1199C R4 5kQ