(a) Determine the reactions at A and E if P- 1010 N. The reactions are positive if to the right or up, negative if to the left or down. (b) What is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads. 26 4380 N B 3.1 m D 5m 5 m Answers: (a) If P= 1010 N, A,- N. Ay= N E,=

Q: A. ADJUST THE GIVEN CLOSED COMPASS TRAVERSE LINE LENGTH OBSERVED BEARINGS FORWARD BACKWARD STA…

A:

Q: The pin support A and roller support B of the bridge truss are supported on concrete abutments. If…

A: Determine the required minimum dimension of the square bearing plates at C and D

Q: nswer all the questions

A:

Q: Identify the supports of the beam shown a. Hinge, internal hinge, roller, internal hinge, roller b.…

A: The following are the support conditions

Q: 5. What happens to the depth of flow when there is an obstruction in the path? a) Remains the same…

A: To find : Effect on depth of flow when there is interaction.

Q: Horizontal Alignment An existing road with a design speed of 85 km/h passes from one tangent through…

A: Horizontal alignment is the positioning of a roadway, as shown in the plan view, using a series of…

Q: GIVEN THE TABLE BELOW. DETERMINE THE FOLLOWING. COURSE DISTANCE (m) BEARING N 58° W S 35° W АВ…

A: In a closed traverse, the algebraic sum of latitudes and departures is zero. The bearing of CD,…

Q: An unknown metal (530 g) is added into a cylindrical container (inside diameter: 5 cm) containing…

A:

Q: Kitchen Bathroom Living Room Dining Room Library Entry Above is the floor plan for a new house. The…

A: The given floor plan is labeled which is shown below: Given scale: 1 inch: 8 feet

Q: W1 A 幸 10 ft 10 ft Set w1 (k/ft) A (1,2,3,4,5) B (6,7,8,9,0) 3. If the given beam has constant El,…

A:

Q: A 300 mm square tied column carries a concentrated DL of 250 kN and LL of 500 kN. Other significant…

A: Footings are a significant piece of foundation development. They are normally made of cement with…

Q: 2: Determine the area required for a new landfill site with a projected life of 20 years for a…

A:

Q: Calculate stress and pore water pressure and determine the total and effective vertical stresses…

A: Finding out total stress, effective stress and pore water pressure diagram.

Q: What is the absolute maximum positive moment in the simply supported beam to the nearest 0.01 k-ft.…

A: Given  P1= 4k  P2= 1.7K  P3= 1K

Q: -a) Soil sampling, and testing. may be thought of as consisting of three steps-boring, a- imputation…

A:

Q: 10. The nature of streamlines in a flow net obtained by the combination of source and sink is- a)…

A:

Q: 1. What is energy per unit head of water called as a) Total energy b) Specific energy c) Velocity…

A: Energy per unit head of water

Q: The bracing for the moment-resisting frame used a channel section. Determine if the channel is…

A:

Q: Problem IlI. A beam shown in Figure 1 is subjected to loads as shown. 59 kN 38 kN/m B 120 kN.m 68 kN…

A:

Q: Problem 1: Design an equalization basin for the following cyclic flow pattern. Provide 10 percent…

A: Solution Time (hr) Flow (m3/s) BOD5 (mg/L) Volume in(m3) Volume out(m3) Accumulation in the…

Q: Determine the specific gravity of the fluid if at a point 9.44 m below the surface, the pressure is…

A: Given Depth (h)=9.44m Pressure (P)=121.69 kPa To find Specific gravity

Q: 40 30 20 20 15+ 10 10 10 15 20 25 30 Air temperature, "C 35 Wind velocity, km/h 4 40 35 30 25 20 15…

A: Calculate the rate of evaporation from the following equation: E=5(Tc+18)2.5-r(Ta+18)2.5V+4×10-6…

Q: If the readings of a Marshall sample as shown below 1- The maximum load that cause failure of it =…

A: Calculate the volume of voids in mixVV=(Gth-GmGth)×100=(2.52-2.512.52)×100=0.397%Calculate the…

Q: A 900 mm diameter pipe 1,800 m long carries 1.2 cu.m./sec from reservoir A, whose water surface is…

A:

Q: 1.0 ft /s of water flows through 100 ft of 6 in steel pipe at a temperature of 70 degrees F. The…

A: Given, Q=1 ft3/s L=100 ft of 6 in T=70°F rd=20ν=0.739×10-5 Diameter= 6 in=0.5 ft

Q: 2. The following results were obtained from liquid limit and plastic limit tests conducted on the…

A:

Q: If the internal radius of a hollow shaft is n times the external radius, then ratio of torques…

A:

Q: PROBLEM: A built up section of A992 steel is made from plates fully welded together. The flanges…

A:

Q: A tank 9.76m long and 1.15m high is uniformly accelerating from rest to 36.08kph. The depth of water…

A: Length of tank = 9.76 m  Height = 1.15 m

Q: An unconfined aquifer is located between two fully penetrating rivers and has a hydraulic…

A:

Q: g that the allowable normal economical wide-flange b» WI

A:

Q: 1. What is the unit weight of aggregate? 2. How do you calculate void content of aggregate? 3. What…

A: 1.The weight or mass of an aggregate needed to fill a container with a given unit volume is its unit…

Q: In the overhanging beam show, determine P so that the moment over each support equals the moment at…

A: Determine P so that the moment over each support equals the moment at the midspan.

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.