a) Determine the force required to just submerge a Size 5 soccer ball (assume 9"diameter) in a swimming pool. Neglect the weight of the soccer ball material & air inside.b) Determine the force required to just submerge a 3ft diameter beach ball in aswimming pool. Neglect the weight of the beach ball material & air inside.c) Do the same calculations for submerging the soccer ball and beach ball but this timein a vat filled with mercury.d) Compare the forces and explain your results.

Answered: a) Determine the force required to just…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

HI! HELP ME PLEASE. THANK U!
A cylindrical steam boiler is to have a volume of 1340 cu ft. The cost of the metal sheets to make boiler should be a minimum. What is the required base diameter in feet? 11.95 18.46 O 12.31 13.64
Select the proper-sized steel tube for a flow rate of 20 gpm and an operating pressure of 1000 psi. The maximum recommended velocity is 20 ft/s and the factor of safety is 8. a) Material is SAE 1010 with a tensile strength of 55,000 psi b) Material is AISI 4130 with a tensile strength of 75,000 psi Can you please show your work in a neat fashion so I can understand it for study purposes. Thanks so much!
A 198 hp (power-shift) dozer is used in a pushing operation. The dozer is equipped with a straight blade. The material (dry and noncohesive) weighs 97 pcf in the bank state. It is estimated the material will swell 6%, from bank to loose state. The center-of mass–to–center-of-mass pushing distance is 200 ft. Job efficiency can be assumed to be equivalent to a 50-min hour. Calculate the production in bcy per hour and the direct cost of the proposed earthmoving operation in dollars per bcy. The company’s normal O&O cost for these machines is $135 per hour and the operator’s wage is $50.00 per hour plus 36% for fringes, insurance, and worker’s compensation.
Fluid Mechanics Will water in a parafin wax capillary tube inserted vertically in a reservoir of water attain a height in the tube greater than or less than the height of the reservoir, and why?
figure below shows the proposed design for a hydraulic press used to compact solid waste. A piston at the right is capable of exerting a force of 12500 lb through connecting rod to the ram. The rod is straight and centrally loaded. it is made from AISI 1040 OQT 1100 steel (Sy=80x10^3 psi, E=30x10^6psi. compute the resulting design factor for this design. specify the required diameter of the connecting rod if it is made as a solid circular cross section. Use design factor of 4.0. ompute the resulting design factor 101 Solid waste to be compacted Emn A Ram Weld A-18m² I= 4.5int Connecting rod 12.75 ft Pin A 2.00 in Section A-A Piston 3.00 in 12 500 lb I= //12 H=4 n=0.
A. Select the most appropriate flow profile (from # 1 to #6 in Figure Q1.A) for each of the fluid types listed below. a. Newtonian b. Shear Thinning c. Shear Thickening Bingham Plastic d. #1 DD y=0 y = ymar P #4 2 #12 #5 P #3 #6
The figure below shows a fabricated assembly made from three different sizes of standard steel tubing listed in Appendix G.2. The larger tube on the left carries 0.075 m3/s of water. The tee branches into two smaller sections as shown. Reducing tee Flow 100-mm OD x 3.5-mm wall steel tube - 160-mm OD x 5.5-mm wall steel tube - 50-mm OD x 1.5-mm wall steel tube Required If the velocity in the 50-mm tube is 10.00 m/s, what is the velocity in the 100-mm tube to the nearest 1000th?
A 40-m-long, 12-mm-diameter pipe with a friction factor of 0.026 is used to siphon 30 °C water from a tank as shown in the figure below. Determine the maximum value of h allowed if there is to be no cavitation within the hose. Neglect minor losses. Use Physicala Properties of Water (SI Units
Fluid mechnics subject A block of wood with uniform horizontal section float in water with 25 cm projecting above the surface. The sameblock when placed in a body of oil (sp. Gr = 0.80) floats with 20 cm projecting above the oil surface.1. Determine the height of the block of wood.
Determine the magnitude of the reaction at A and B dur to hydrostatic pressure?

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS