a) Determine the coefficients In the equations below using the mesh current phasors defined in the circuit diagram. Use the indicated directions of the mesh current and polarities of the voltages. Left mesh: a, +a;z lg +a;3 lc = 20 Middle mesh: a, lt azz le t @za le = 0 Right mesh: a, + agz lg + aa le = 0 When writing these equations, simply enter the coefficients in terms of the impedances withour trying to simplify the math at all. b) Solve for the mesh current phasors as defined in the image below. c) Determine the phase and amplitude of the voitage v(t). The phase should be in degrees between -180' and 180, 3 ΚΩ ww 2 kQ 2H ww lll 20 cos 3000r V I kQ Va(t)

a) Determine the coefficients In the equations below using the mesh current phasors defined in the circuit diagram. Use the indicated directions of the mesh current and polarities of the voltages. Left mesh: a, +a;z lg +a;3 lc = 20 Middle mesh: a, lt azz le t @za le = 0 Right mesh: a, + agz lg + aa le = 0 When writing these equations, simply enter the coefficients in terms of the impedances withour trying to simplify the math at all. b) Solve for the mesh current phasors as defined in the image below. c) Determine the phase and amplitude of the voitage v(t). The phase should be in degrees between -180' and 180, 3 ΚΩ ww 2 kQ 2H ww lll 20 cos 3000r V I kQ Va(t)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve the power triangle at Z6 using the following network law below.4.) Superposition TheoremGiven:V1, V2, and V3 = 220∠0° V, 50 HzZ1 = 7+j8 ohmsZ2 = 6+j3 ohmsZ3 = 5+j5 ohmsZ4 = 2+j3 ohmsZ5 = 8+j4 ohmsZ6 = 1+j9 ohms
Question #2 Find VO using Thevenin's theorem. Find Zth and Vth and then find VO. w L=2 ohm, (1/ w c) = 3 ohm. All resistors are 2 ohm.. All answers should be in magnitude and angle. Draw a phasor diagram showing Vth, VO, and the current flowing through L. lav w +v,
A4 The circuit showed in Figure A4, is powered by an AC voltage source Vs. Sketch the phasor notation for the currents and admittances in the circuit. Tip: the admittance Y is defined as 1/Z, where Z is an impedance. a. Current phasor sketch. b. Admittance phasor sketch. c. Calculate the inductive reactance, assuming the following values: L = 12 mH, frequency = 1.5 kHz. V₂ S R VR FIGURE A4 2 ell VL
Place your final answers for this problem in the correct boxes at the bottom of this page. Use the value Zdegrees notation for representing phasors. Bold terms are expected to be phasors. Vs = 1020 degrees, R = 100 Ohms, L=2 H Vs S + Zin, → R ww IR I₂ ell 1. What is VL if w-10 rad/sec? 2. What is VL if w=100 rad/sec? 3. What is VL if w=1000 rad/sec? 4. Derive the voltage transfer function starting with KCL and ending with VL Vs + VL
What is the value of Thevenins impedance (ZTH) if VTH (the voltage between A and B) is 2 V
This one.
Solve the power triangle at Z6 using the following network law below. Thanks!!!6.) Norton's TheoremGiven:V1, V2, and V3 = 220∠0° V, 50 HzZ1 = 7+j8 ohmsZ2 = 6+j3 ohmsZ3 = 5+j5 ohmsZ4 = 2+j3 ohmsZ5 = 8+j4 ohmsZ6 = 1+j9 ohms
Use the following values: ZR=8 Ohms ZL=30j Ohms Write the final answer to at least 5 significant figures.
Please answer question 3 with details on how to do it. Make handwriting legible please. Thank you.
× Superposition) For the circuit below use Superposition to determine the Current Magnitude/Direction and Voltage for each component.. R₁ = 20 S www R2: V₁ = 20 V V₂ = 10 V www R₂ = 10 Use the provided boxes in the circuit to draw an arrow to indicate the direction of onventional current through each component. IRI: VR1: VR2:
Draw the AC equivalent circuit for the circuit shown below. Find Z¡ , Zo and Ay. Vcc 20V B = 100 re = 100 ro = 500kn %3D 100kn :1kn 10UF 1ko 10kn 40H2 10kn ww
b) a) For the circuit shown in figure 3, use nodal analysis to obtain a complete set of circuit equations, presenting your answer in matrix form. Compute the potential across and the current flowing through the ZL element, given: IS = 12sin(wt) A, R1 = 3 0, R2 = 50, L1=j4Q, L2=j10 Q and ZL = (2+j2) Q IS R1 m L2 R2 ZL Figure 3 Using equations and text, define the two-port impedance parameters.