Vc+15 VRC11.5k2R1>4.7k2Q2VoRsQ1R21k2RE21502RL1k2VsRE13302ZinZoAssume hfe=ß=100 and Vbe=0.7V for Ql and Q2(a) Determine IC1, VCE1, and hiej of Q1.(b) Determine Ic2, VCE2, and, hiez of Q2.(c) Determine Zin and Zo.(d) Determine the current gain Ais=lo/Is.(e) Determine the voltage gain Avs=Vo/Vs.(f) Determine Is, Ib2, and Io if Vs=200mVp-p

"According to the Comapny's policy we will solve the first three parts of the question". Given the…

(a) Determine IC1, VCE1, and hiej of QI. (b) Determine Ic2, VCE2, and, hie2 of Q2. (c) Determine Zin and Zo. (d) Determine the current gain Ais=Io/Is. (e) Determine the voltage gain Avs=Vo/Vs. (1) Determine Is, Ib2, and Io if Vs=200mVp-p

(a) Determine IC1, VCE1, and hiej of QI. (b) Determine Ic2, VCE2, and, hie2 of Q2. (c) Determine Zin and Zo. (d) Determine the current gain Ais=Io/Is. (e) Determine the voltage gain Avs=Vo/Vs. (1) Determine Is, Ib2, and Io if Vs=200mVp-p

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
ELECTRONICS LAB COURSE
Give me List of electrical circuit components. A three-input CML XOR gate using BJTS (bipolar junction transistors) is shown below: RC2 RCI Q9 Q10 Q7 Q8 C Q5 Q6 OB Q3 Q4 В Q2 Qi IEE -VEE
TRUE OR FALSE Increasing R2 increases the single-ended and double-ended differential mode gains of the differentialamplifier. Increasing R2 decreases the transistor DC currents and decreases the DC output voltages.
Subject: Engineering Electronics In 150 words or more: Kindly answer the question in essay form. How do the biasing polarities differ between npn and pnp transistors? Subject: Engineering Electronics
3. Refer to the Characteristic curve shown in Figure I a. Draw a load line on the characteristics determined by VE = 24 V and = 3k for a fixed bias configuration. Rc b. Choose an operating point midway between cutoff and saturation. Determine the value of Rg to establish the resulting operating point. c. What are the resulting values of Ico and VCEQ? d. What is the value of ẞ at the operating point? e. What is the saturation, Icsat current for the design f. What is the dc power dissipated by the device at the operating point? g. What is the power supplied by Vcc h. Determine the power dissipated by the resistive elements Vcc ac input o signal HH C₁ Ra Is 'c}+₁ Rc VBEE Ic HE C₂ VCE ac - output signal
given that V1 = 10 volt and V2 = 20 volt . what is value of output voltage. explain ...
A - Explain the symbols, operating principles and usage areas of the diodes given below. (Zener diode: photo diode: led diode: opto coupler) B- Draw the voltage trigger circuit and explain its operation. Explain how there is a difference between the voltage quadrant and the tripler
c) Figure 2.3 shows the circuit diagram of a typical npn BJT common emitter amplifier. The values of RB1-30 kOhm, RB2=10.XY kOhm, Rc-3.XY kOhm, Ic=2.XY mA and Vcc=24 V. If the transistor current gain 3 = 50 determine using the full analysis and assuming VBE = 0.7 V the value of RE, hence identify the location of the Q-point (Ic, VCE, IB and VBE). Now sketch the AC circuit model of this amplifier and determine the value of the ac open circuit voltage gain Av and the ac short circuit current gain Ai. (Assume that Vth = 26 mV). Vin RB1 Cin lin RB2 -10 Rc VB RE + Vcc Vc Cout VE www li Figure 2.3 Vout Ce ¡out x=1 y=7
Figure 2. illustrates a transistor amplifier implemented with a transistor (we can use PN2222 data here) and two resistors, which receives the operating voltage from a 10 V voltage source. Current gain of the npn- transistor ß=hFE = 100. Calculate a) base current IB b) collector current, Ic c) collector-emitter-voltage UCE d) determine in which state the transistor is operating (saturation, cut off, active) RB IB Rc Ic +il+ Vcc Figure 2. Npn - transistor connection. RB-300 kn, Rc-2k2, Vcc= 10 V.
Give the information below. Determine: 2 Given the emitter stabilized bias circuit, DC Equivalent Circuit Base Emitter Loop. Derive formula. Collector Emitter Loop. Derive determine. 1 2 20 V formula. 4 Solve the unknown values: 2.4 k2 a IB 510 k2 IcQ oVc b Ic VB VCE VCEQ B= 100 Vc IBQ VB e OVE f VE 1.5 k2
help PLZ as fast as you can