A Delta Modulation system is designed to operate at 3 times the Nyquist rate for a signal with a 3 KHz bandwidth. The quantization step size is 250mV. i) Determine the maximum amplitude of a 1 KHz input sinusoid for which the delta modulator does not show slope overload. Determine the postfiltered output SNR for the signal of part (i). ii)

A Delta Modulation system is designed to operate at 3 times the Nyquist rate for a signal with a 3 KHz bandwidth. The quantization step size is 250mV. i) Determine the maximum amplitude of a 1 KHz input sinusoid for which the delta modulator does not show slope overload. Determine the postfiltered output SNR for the signal of part (i). ii)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q: Explain in details with all figures and equations the modulation index of Amplitude Modulation (AM) and then show the AM wave when the modulation index > 1 , modulation index < 1 and modulation index =1.choose the best case and why.1-draw the three cases.2-write an example.
4. The information in an analog voltage waveform is to be transmitted over a PCM system with a F 0.2% accuracy (full scale). The analog waveform has a bandwidth of 200 Hz, and an amplitude range of -5 to +5 V. determine the following: - The minimum sampling rate needed. - The number of bits needed in each PCM word. - The minimum bit rate in the PCM signal. - The minimum channel bandwidth for transmission of this PCM signal.
AF ADM system is designed to operate at 3 times the Nyquist rate for a signal with a 3 kHz bandwidth. The quantizing step size is 250 mV. *** (i) Determine the maximum amplitude of a 1-kHz input siinusoid for which the delta modulator does not show slope overload. (ii) Determine the posfiltered output part (i) signal-to-quantizing-noise ratio for the signal of
Does a PCM signal have a smaller bandwidth? Why or Why not?
3. The role of mixer in the Armstrong modulator is to. a) raise the carrier frequency b) lower the carrier frequency c) to change the carrier frequency to any required value For AMDSB-SC, The carrier is suppressed using a) A mixer b) A frequency multiplier c) A balance modulator 5. In FM modulation, frequency deviation is equal to .........., if the amplitude of the modulating signal is 4 V, and the frequency sensitivity of the modulator is 30 Hz/V. a) 120 Hz b) 34 Hz c) 100 Hz 6. A voltage controlled oscillator (VCO) is an oscillator that its frequency output is varied according to any change in the ............... at its input. 4. a) Frequency b) Current c) Voltage Q1: (B) Draw A block diagram to generate the SSB using Hilbert Transform method, Write an equation for an input, and output signals?
What is the main disadvantage of linear delta modulation? What is the solution for this problem? this question from digital communication course.
what happens when the modulation order is increased for a modulated signal?
The baseband signal modulates a 98 kHz carrier sine wave. Using frequency and amplitude labelling similar to that in Figure 2, sketch the spectrum of the modulated signal using a template, similar to that in Figure 3, for the following modulations: AM with the amplitude of the carrier wave being 20 V DSBSC SSB – the lower sideband SSB – the upper sideband
It's urgent please solve ASAP.
The modulation index of the PM signal is 2. If a modulating signal that has amplitude of 50 mV at a frequency of 3 kHz phase modulates a 90 kHz carrier signal, what would be the new modulation index of the signal? Assume that the amplitude of the modulating signal is increased by 50%.