A decision is to be made on the most suitable sites between A, B, C, and D forconstructing a landfill for managing industrial wastes in a city based on soil type, landslope, geology, and land use. Use the following information and analytical hierarchyprocess to support the decision on the preferred siteFACTORSite A Site BSite CSite DSoil type3134Slope1223Geology3122Land use1113Soil depth3113SCALEDSCORESuitable1Moderate2Slight3Not Suitable4

Here is some information you can use, hope it can help you and Godbless.

Answered: A decision is to be made on the most…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given the following Atmospheric Data: Altitude (m) Pressure (kPa)0 - 101.331000 - 89.872000 - 79.503000 - 70.114000 - 61.66 Use linear interpolation to estimate the atmospheric pressure at: Altitude (m) Pressure (kPa)4MM ?2689 ?3500 ? (where MM is your birth month, so if you were born in December, evaluate at 312 meters)
Q2//A moist chunk of 25kg soil had a volume of 12000 cm³. After it is dried in an oven, the weight of the dry soil becomes 23kg. The specific gravity of the soil GS material is 2.65. Determine Water content, Unit weight of moist soil, Void ratio, Porosity, and Degree of Saturation.
Q1. Honey is a very widely used ingredient in cooking all around the world. Many commercial honey manufacturers heat treat honey to remove harmful bacteria that may be present. The density and viscosity of the honey varies with temperature, as shown in table 1. Temperature K 293 298 303 308 313 318 323 Density kg/m³ 1403 1398 1393 1388 1383 1378 1373 Viscosity Pas 55.66 46.45 37.99 30.28 23.32 17.11 11.65 Table 1: Fluid properties of honey. A particular processing facility heats and sterilises 500 kg of unprocessed honey every 30 minutes. The unpro- cessed honey is stored in large vats, then pumped though pipes into heating units before being pumped through another pipe to be bottled. The pipe carrying the honey from a storage container, which is 11 m tall, to a heating unit is 5 m long and has a diameter of 10 cm. Prior to being heated the honey is kept at 25°C. (a) What is the pressure difference between the top and bottom of a storage vat when it is full? (b) What is the volume flow…
What is the melting temperature of pure Sn? Group of answer choices 327 °C 232 °C Cannot determine from the provided information. 183 °C
Problem 1 (Lecture 03) Three forces act on the bracket shown to the right. Note that for this problem, the direction (0) of F1 is measured from the positive x' axis, positive clockwise. Complete the following: a) Determine the direction (0) and magnitude of F₁ so that the overall resultant force is directed along the positive x' axis and has a magnitude of 1 kN. b) Determine the unit vector u₂ (in Cartesian notation) for the direction of F2. y Ꮎ F₁ F₂ 45° 30° = 450 N F3 = 200 N X
The fuel gage for a gasoline tank in a car reads proportional to its bottom gage. The tank is 35 cm deep and accidentally contaminated with 3 cm of water. Specific gravity of gasoline is 0.68. If the tank has a uniform horizontal cross-sectional area of 0.45 m2, how many liters of gasoline are required to fill the tank? Select the correct response: 9.53 L 7.41 L 6.35L 8.47L The fuel gage for a gasoline tank in a car reads proportional to its bottom gage. The tank is 35 cm deep and accidentally contaminated with 3 cm of water. Specific gravity of gasoline is 0.68. What is the gage reading when the tank is filled with gasoline? Select the correct response 2.87 kPa 2.11 kPa 2.56 kPa 2.34 kPa

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS