A DC Wheatstone bridge used in an electronic systemis fed by 200V Battery as shown in figure Q19. Thevalues of arm resistances are R1 = 10 Q, R2 = 10 Q%3|and R3 = 20 . Then, the value of R4 is calculated as,ITotalI2R3R,• Vout(Vc-Vo)VsDR2R4Figure Q19.а. 20 ohmsb. 30 ohmsC. 40 ohmsd. 50 ohmsB.

Given : R1 = 10 ohm R2 = 10 ohm R3 = 20 ohm R4 = ? V = 200 V By the help of…

A DC Wheatstone bridge used in an electronic system is fed by 200V Battery as shown in figure Q19. The values of arm resistances are R1 = 10 Q, R2 = 10 Q %3D and R3 = 20 . Then, the value of R4 is calculated as, ITotal I2 R3 R, • Vout (Vc-VD) Vs D R2 R4 Figure Q19. a. 20 ohms b. 30 ohms C. 40 ohms d. 50 ohms B.

A DC Wheatstone bridge used in an electronic system is fed by 200V Battery as shown in figure Q19. The values of arm resistances are R1 = 10 Q, R2 = 10 Q %3D and R3 = 20 . Then, the value of R4 is calculated as, ITotal I2 R3 R, • Vout (Vc-VD) Vs D R2 R4 Figure Q19. a. 20 ohms b. 30 ohms C. 40 ohms d. 50 ohms B.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2: Kelvin double bridge uses: Inner ratio arms = 300 and 350 Outer ratio arms = 200 and 40 Q If the resistance of the connecting leads from standard to unknown resistance is 60 mQ. Calculate Standard resistance if the unknown resistanceis 300 O 60.000019Q 60.000160 60000.150 60.0001950
Load cells are used for the measurement of:Select one:a. Velocity O b. StrainO c. WeightO d. Stress
Compute for the equivalent resistance across terminal cd, and explain why the equivalent resistance is like that. Show completer solution
Determine the approximate value of VGG of Figure 522. VDD T17V 1.8kO Q1 V, = 9.8V 1MQ pss = 9mA V =- 4.5V EVGG Figure 522. -1.5 V O -1.2 V -1.453 V -3.281 V
Two resistors, R1 and R2 are connected in parallel. The individual resistance measurements, using digital ohmmeter, give R1-20.35 and R2= 15.735 Q. The total resistance to the appropriate number of significant figure is .........
Can you please help me with this problem?
Problems I A potentiometer with a uniform resistamce per unit length of track has a total resistance of 2 k2 and a supply voltage of 10 V is connected across it. The output from the potentiometer is connected across a load of resistance 5 k2 What will be the error due to this loading when the slider is at the mid-point of the potentiometer track? -2 A potentiometer with a uniform resistance per unit length of track is to have a track length of 100 mm and used with the output being measured with an instrument of resistance 10 k2. Determine the resistance
W1 A 1 IL Tr1 AC Supply V V w2 12 Tr2 use double range voltmeter Fig.(1)
Pt A 6v battey, delivrers loMA to thvee resistors in faralkl, R, =1kr,R2 =2K2,R3=Rx- Calcalate: a) Current in b) Power dissipatiod by Rx and R,-[Anss 6mw, 36mn. c) Resistance ratio Rx/R--(Ans: 6/)- d) Current ratio Ii/Ix. Anst 6/4). Rx stheatis Ix Anss 1 mÁ)
A Read aloud V Draw aye viev Engineering Problems #7 March, 8 Four resistors are connected in parallel across a 200-mA independent cur rent source as shown in Figure P24. What is the voltage across the resistors and the current in each resistor? 200 mA U 009 U 001 U 08
The voltage source V1= 250 V with internal resistance R1= 2ohm in Figure 2.1 will feed the RL resistor with a transformer with a conversion ratio of 1/16 and considered ideal. What should be the value (RL) of the RL resistor to be placed so that the RL resistor can draw maximum power from the voltage source? What is the power (Pvi) consumed by the voltage source when the RL resistor you found is active? In this case, how much power (Pri) is spent on the internal resistance of the source, the resistor R1?RL=Pv=PRI =
Find out the IT and RT for the given circuit: Attach simulation screenshot.