A d.e, series machine rated at 200V, 100A has an armature resistance of 0.12 and fieldresistance of 0.15 Q. The friction and windage loss is 1500W . Use a Vaace of 200V andan Isne of 100A . Use the above information to answer Q17 – Q2117.Calculate the per unit value of the total series resistance of the machine.a) 0.125b) 0.135c) 0.145d) 0.155none18.Calculate the per unit value of the friction and windage loss.a) 0.092b) 0.075c) 0.032d) 0.015e) noneCalculate the per unit value of the total series resistance loss at the rated load.19.3a) 0.551b) 0.356c) 0.532d) 0.650none20.Calculate the per unit value of the total power loss at the rated load.a) 0.30b) 0.20c) 0.15d) 0.50e) none21.Calculate the per unit value of the efficiency of the machine.a) 0.47b) 0.83c) 0.89d)0.65e) none

As per the guidelines, we supposed to answer first three part of the question at a time so please…

A dc series machine rated at 200V, 100A has an armature resistance of 0.12 and field resistance of 0.150. The friction and windage loss is 1500W. Use a Vrase of 200V and an Isare of 100A. Use the above information to answer Q17 – Q21

A dc series machine rated at 200V, 100A has an armature resistance of 0.12 and field resistance of 0.150. The friction and windage loss is 1500W. Use a Vrase of 200V and an Isare of 100A. Use the above information to answer Q17 – Q21

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

At rated load, a shunt motor draws an armature current of 100 A from a 240 V source while running at 1000 rpm producing a back emf of 228 V. At no load, the armature current drops to 5 A that produces a back emf of 235 V. How fast does the motor run at no load?
A 6-pole, 24 KW, 120 V, DC machine has a Duplex LAP-wound armature which has 72 coils with 10 turns per coil. Its rated speed is 2400 RPM. Assume a dead zone of 6 coils that are always beyondpoles faces. Assume no internal losses in the machine. Calculate the current per pathin the armature of this machine if its load is 21.5 KW. Select one: a. Ioath = 179.17 A b. None C. Ipath = 14.93 A d. Ipath = 16.167 A
dc machines
2. A 15 kW shunt machine having an Armature circuit Resistance of 0.35 Q and a filed resistance of 1002, generates a terminal voltage of 240 V at full load. Find the Efficiency When I. act as a Generator at full load . II. act as a Generator at half load III. act as a Motor
A 220 V dc machine has an armature resistance of 1ohm if the full load current is 20 A, the difference of induced voltage, when the machine is running as a motor and generator, is *
i need the answer quickly
A 220 V permanent magnets DC motor has an armature resistance of 0.5 0. If the full load armature current is 20 A, find the induced e.m.f.. Select one Ⓒa. 210 V b. 230 V c. Not on the list d. 240 V O e. 220 V
i need the answer quickly
The armature circuit of a free excited direct current motor with a nominal voltage of 600 V is fed from an adjusted direct voltage source. The excitation circuit is also powered from a regulated voltage source. It is used in an application that requires motor speed adjustment. The speed of the motor at the nominal armature voltage was measured as 1600 rpm. All losses of the motor and voltage source and the effect of armature reaction are neglected. It is accepted that the engine is not saturated.Answer the questions below.a) Draw the armature and excitation circuit of the motor and write the formulas for the equivalent circuit.b) If the load moment of the motor at the nominal armature voltage is 420 Nm, then calculate the armature current and the input power of the motor.c) If the armature voltage of the motor is kept constant at 600 V and the excitation current is decreased until the speed reaches 4000 rpm, then calculate the shaft moment. Show this working area on the M = f (W) axis.
A D.C. series motor of resistance 1 ohm between terminals runs at 800 r.p.m. at200 V with a current of 50 A. Find the speed at which it will run when connectedin series with a 5 ohms resistance and taking the same current.
Q3) The armature of a 4-pole DC machine has 240 coils wound in lap formation. Each coil generates a voltage of 4 V and carries a current of S A. a) Calculate the total generated voltage in the armature,Eg. b) Find the current in each parallel path and total armature current. c) If the armature is rewound in wave formation, find the generated voltage, Eg. current per path and total armature current. Assume number of coils are fixed at 240.
Complete solution pls. Thank you