A DC motor rotating at 1800 RPM with 180 Volts and 48 Amp line current. The copper losses were measured as 480 Watt. Find the Power converted from electrical to mechanical and how much torque is induced by this motor Select one: O a. None %3D O b. Pcony = 8.16 KW and Induced Torque = 43.3 N.m. %3D O c. Pcony = 8640 W and Induced Torque = 0.46 KN.m. %3D %3D O d. Pconv = 8.64 KW and Induced Torque = 45.84 N.m. %3D

A DC motor rotating at 1800 RPM with 180 Volts and 48 Amp line current. The copper losses were measured as 480 Watt. Find the Power converted from electrical to mechanical and how much torque is induced by this motor Select one: O a. None %3D O b. Pcony = 8.16 KW and Induced Torque = 43.3 N.m. %3D O c. Pcony = 8640 W and Induced Torque = 0.46 KN.m. %3D %3D O d. Pconv = 8.64 KW and Induced Torque = 45.84 N.m. %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Urgent need.
The voltage a cross the terminals of a certain 3-phase machine is 400 <40 ͦ V whereas the current which is assumed to be into this machine is 55<-60 ͦ Find the real and reactive powers consumed or delivered by this machine. What is the type of this machine?
A. The brushes used in a DC generator a) ride against the commutator segments. b) are made from material softer than the commutator segments. c) are generally marked Al and A2 d) all of the above B. A magneto is a DC generator that uses for its pole pieces. a) electromagnets b) permanent magnets c) either "a" or "b" d) neither "a" nor "b"
3- A shunt machine connected to 250V mains has an armature resistance (including brushes) of 0.120 and the resistance of the field circuit is 1002. Find the ratio of the speed as a generator to the speed as a motor. The line current in each case being 80A 1001 W 200
.A 110-V dc motor draws a current of 3OA and is located 500 ft from the power source. What is the supply voltage if the diameter of the copper is 0.25 inch?
divided by rpm. Torque equals horsepower 5252 a. b. horsepower x 5252 voltage x horsepower C. d.
A 3-phase, 60 Hz, Y-connected, AC generator has a stator with 60 slots, each slot contains 12 conductors. The conductors of each phase are connected in series. The flux per pole in the machine is 0.05 Wb. The speed of rotation of the magnetic field is 720 RPM. What are the resulting RMS phase voltage and RMS line voltage of this stator? Select one: O a. V = 2262.0 Volts and Vr = 3917.8 Volts O b. V = 2770 Volts and VT = 2770 Volts O c. Vộ = 1599.4 Volts and VT = 1599.4 Volts O d. V = 1599.4 Volts and VT = 2770 Volts O e. None
The torque in AC machines depends on Select one: a. The strength of the rotor magnetic field b.The strength of the external magnetic field c.The sin of the angle between the rotor magnetic field and the external magnetic field d.A constant representing the construction of the machine e.All of above Clear my choice
A shunt generator delivers 1,000 W at 149 V to a load. If the armature resistance is 0 ohm, and the shunt field resistance is 56 ohms, calculate the shunt field current in ampere.
A dynamo has a iron loss of 1100 W of which 65% is the hysteresis loss when operated at a speed of 1300 rpm. Assuming the flux to remain unchanged, what will be the iron loss when the speed is increased by 10% ?
Show detailed solution with illustration.
A 220 V DC machine has an armature resistance of 1 Q. If the full load current is 20 A, what is the difference in induced voltage when the machine is running as generator and motor under full load condition