A DC motor has the following parameters: K₁ K₁-0.2 N-m/A, c-5x10 N-m-s/rad, R.-0.8ohm. (a) Assuming steady-state response, obtain the expressions for the no-load speed, the no-load current, and the stall torque. (Assume v, is a variable with unknown value). (b) The datasheet states that the motor's maximum speed is 3500rpm and the maximum current is 40A. Determine if the motor can be used with an applied voltage of v, 15V.

A DC motor has the following parameters: K₁ K₁-0.2 N-m/A, c-5x10 N-m-s/rad, R.-0.8ohm. (a) Assuming steady-state response, obtain the expressions for the no-load speed, the no-load current, and the stall torque. (Assume v, is a variable with unknown value). (b) The datasheet states that the motor's maximum speed is 3500rpm and the maximum current is 40A. Determine if the motor can be used with an applied voltage of v, 15V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 3 ALoad torque=Tload= 8 Nma) 143 rpmb) 734 rpmc) 1361 rpm d) 77 rpm e) 1333 rpm
For a 18600W 2400rpm DC motor, the following values are given: Ra = 0.089 2 (value at room temperature (250C)), La = 0.00144 H, KT = 0.85 Nm / A and KV = 0.851 V / (rad / s)), (In calculations Use the hot resistance values at 1000C.) (Take the rated field winding losses as Wf= 210W.) If this DC machine is operating as a motor with rated flux at rated speed, calculate the rated torque (TR), rated current (IR), rated voltage (VR), efficiency (n) at the rated point, taking into account the winding losses. Find the speed (@NL) of this motor in no-load condition. TR Nm IR А VR V Eff = % ONL= rpm
Induct.motor.
DC generators
A 3-phase and 6-pole asynchronous motor is fed from a 100 Hz source. The engine speed under a certain load is up to 1940 rpm. If the load torque of the motor decreases by 20%, which of the following will the new speed of the motor be as given? (Note: You can think of the speed-torque relationship of the motor as linear in the steady operation region.) a.1979 rpm b.1976 rpm c.1952 rpm D.1967 rpm e.1928 rpm
12. The IR-compensation in frequency control of induction motors is used for: a) compensation of the voltage drop in the active resistance of the stator winding. b) compensation of the voltage drop in the inductive reactance of the stator winding. c) keeping the motor voltage constant. d) keeping the motor speed constant U₁ U₁ Us0 0 f. f₁
Angular speed of a DC motor running at a speed of 1200rpm is ................. Answer
Hi .. This is simulation starting synchronous motor in matlab 2012 who can I find the power factor by use this simulation and what is the elemen add to find the power factor
Subject: Electrical Machines
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm
Solve as soon as possible
Describe the basic circuit of DC Generators including its yoke, fid windings, interpoles, fieldpoles, difference of shunt coils and series coils, commutator and brushes ?