A damper square mat is supporting a dead load weight of 8 kN. Helical springs will be used to support the load located at all corners with shearing stress of 120.6 Mpa at 20 turns. The spring has a deformation of 98.7 mm with a mean radius of 80 mm. Design the minimum diameter of the wire to support a load. Use G = 83 Gpa.

Q: please solve and explain using values below

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: PROBLEM 1 For the assembly shown, determine the displacement of point B and D as the load of 50KN is…

A:

Q: The steel link AB of the wire cutter has a dimensions of 3mmx 10mm, and modulus of elasticity of…

A:

Q: If during the application the bearing subjected to an equivalent radial load of 1.07 kN, and the…

A:

Q: art ● pus ents es Three cables having an area of 0.05 in² each is carrying the load W as shown. With…

A: To find: The stress in longest cable. Given: The load is W=1500 lb. The length of the three cables…

Q: below shows a stee! bar 07 mass m The 7igure which is placed against a wall. There is no betneen the…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: the maximum force, P (in lbs) wit

A:

Q: The crank is loaded by a single force F, = 200 lb which causes twisting and bending of the 1-in…

A:

Q: the height (in mm) of cross section from strength calculation           h = ?

A: working stress = yeild stress/ factor of safety = 220/1.6 = 137.5 MPa

Q: The assembly shown consists of the solid steel shaft (1) with a diameter of D₁ = 14 in and a copper…

A: According to the given dataThe outer diameter of the BC=D2=7.5 int2=0.35 inThe diameter of the…

Q: Determine the modulus of resilience for each of the following grades of structural steel: (a) | ASTM…

A: Data given-

Q: A helical spring has a shearing stress of 120.6 Mpa with 20 turns. The spring has a deformation of…

A: Given Data⇒ Helical Spring Shearing Stressζ=120.6 MPaNumber of turnsN=20 turnsDeformation∂=98.7…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: The helical compression spring is made of 12mm wire diameter with 132 mm mean diameter. Determine…

A: Given that,

Q: The solid shaft AB has a d= (3.5 + 0.4 a) in. and shaft BC has a d shafts AB and BC have the same E…

A:

Q: Determine the forces in members CD, CJ, and DJ.

A:

Q: Determine the magnitude of the pin force at A. Assume W - 875 lb, a 2.9 ft, b-2.4ft, r - 6 in. "" W…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: A spring with 12 active coils and a spring index of 9 supports a static load of 220 N with a…

A: Given data as per the question Active coils =12Spring index =9static load =220NDeflection =120…

Q: P = 20 kN Mv = 600 Nm.

A: GivenP=20kNMV=600Nm=600×103 NmmD1=34mmD2=40 mmD3=36mmR1=5mmR2=2mmη=0.45

Q: The wire-mass system shown is constructed using 6061-T6 aluminum wire. Determine the minimum…

A:

Q: Q1: The shaft (AB) is supp rted on the bearings A and B as shown in figure below. The shaft is…

A: Given:Tension in the rope, T=4.5 kN or 4500 NFactor of safety, Fos=2diameter of drum, d=200 mm

Q: A spring is made of 2.0 mm diameter music wire A228 (set not removed). Determine its maximum…

A: music wire A228 (set not removed).Diameter of music wire = 2 mm

Q: Determine the wahl's factor of a spring designed to fire a 3kg projectile. The outside diameter of…

A:

Q: factor of safet

A: d= 40mmF = 29KNL = 796mmT = 1.7KNmfail stress = 156MPamaterial- brittle cast iron

Q: Required information This problem illustrates that the factor of safety for a machine element…

A: F = 0.55 kNP = 4 kN or 4000 NT = 25 N.mSy = 280 MPaLength of the bar, L = 100 mmDiameter of the bar,…

Q: A vertical rod of length L and diameter d is fixed at its upper end and carries a load Wat its lower…

A:

Q: Two parts of a machine, both made from steel, are held together by 9 equally-spaced M6 x 1.0 grade…

A: Smaller value of FOS is 2.60 which is For joint separation under the applied load.Explanation:Given…

Q: A damper square mat is supporting a dead load weight of 8 kN. Helical springs will be used to…

A: Find the diameter of wire Deformation = 98.7 mm Stress = 120.6 Mpa Force = 8 kN

Q: determine the minimum preferred size diameter.

A: Given: FOS=3  T2=0.15T2 To determine: The minimum diameter using distortion energy theory

Q: Please solve the problem with a free body diagram. Write the explanation. Strictly don't use…

A: Step 1: Step 2: Step 3: Step 4:

Q: = 69.0 psi. In a test on an aerosol can it was loaded to a gage pressure p While pressurized, the…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given: The force at B = 3 kN The force at C = 5.4 kN

Q: Use the von Mises failure criterion to solve for the minimum required yield stress if a factor of…

A: GIVEN DATA- σX =100MPa σY=-78MPa τXY = 30MPa WE HAVE TO CALCULATE YIELD STRESS ACCORDING TO VON…

Q: What is the maximum possible value of theclamping force C in the jaws of the pliers shown inthe…

A: Given; The diameter of the pin = 5 mm The ultimate shear stress = 340 MPa The factor of safety = 3

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.