A d.c. shunt generator, runs at 1200 r.p.m. When the machine is driven at rated speed, the no-load saturation curve is shown below. What will be the e.m.f generator, If the field rheostat is adjusted to give a field current of 2.5 A and the machine is driven at 1050 r.p.m when the load current is at the rated value? * Armature voltage (V): 6 32 78 105 127 140 143 146 148 Field current (A) : 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 160V O 122.5V 111.125V 145.142V

A d.c. shunt generator, runs at 1200 r.p.m. When the machine is driven at rated speed, the no-load saturation curve is shown below. What will be the e.m.f generator, If the field rheostat is adjusted to give a field current of 2.5 A and the machine is driven at 1050 r.p.m when the load current is at the rated value? * Armature voltage (V): 6 32 78 105 127 140 143 146 148 Field current (A) : 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 160V O 122.5V 111.125V 145.142V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 4 pole DC shunt generator with a shunt field resistance of 109 ohms and an armature resistance of 1.5 ohms has 282 wave connected conductors in its armature. The flux per pole is 0.02 Wb. If load resistance of 28 ohms is connected across the armature terminals and the generator is driven at 875 rpm. Calculate, The terminal voltage is = The power absorbed by the load is =
In a DC shunt generator, the induced EMF is 230 V, the armature resistance is 0.1ohm and the armature current is 200 A. Determine the terminal voltage.
4. The commercial efficoency of a shunt generator is maximum when its variable kon oquals...loss. a. constant e. iroa b. stray d. friction and windage 5. The basic requirement of a d.c. armature winding is that it must be a. a closed one b.a lap winding e.a wave winding d. either (b) or (e).
A 2 pole wave wound dc shunt generator runs at a speed of 750 rpm, has an armature and shunt field resistance of 0.4 and 580 respectively. The armature has 960 conductors and flux per pole is 0.115 Weber. If the lamp load connected has a resistance of 70 determine (i) Generated EMF, (ii) Total Resistance, (iii) Armature Current, (iv) Terminal Voltage.
A shunt DC motor is supplied by 520V terminals voltage and is used to supply a mechanical load with rotating speed of 1000rpm. The armature is wave-wound and has 500 conductors. The useful flux per pole is 0.03Wb and there are 4 poles (2 pairs of poles). The armature resistance is 0.4 Ohms. Calculate: 1.The internal emf of the motor. 2.The armature current. CLEAR AND CORRECT OR DISLIKE
A 6 pole, wave wound DC shunt generator has a useful total flux of 420 mWb. The armature winding consists of 220 turns each of 0.004 2 resistance, when running at 900 RPM the armature current is 50 A. If the armature winding reconnected as lap calculate the terminal voltage in case of wave and lap given that the field circuit and the speed are kept same.
Q 4. An 8-pole DC generator has 400 armature conductors and a useful flux of 0.05 Wb. What will be the emf generated if it is lap wound and runs at 1,500 rpm? What must be the speed at which it is to be driven to induce the same voltage if it is wave wound? (Ans. 500 V; 375 rpm) 05 A vave wound armature generator has 51 slots Fach slot contains 20 conductors The
1. A machine delivers power to the load at 220 V while being driven at 1,050 rpm. At this load, the armature circuit dissipates 650 W. The armature of a 6-pole separately excited dc generator is lap wound with 534 conductors. If the flux per pole of this generator is 30- mWb, determine the kW rating of the load served. Assume a total brush contact drop of 1.5 V.