A d.c. shunt generator has 6 pole, 34 conductors, lap-wound, with terminal voltage of 210 volts delivering 11 amps to the load, has armature and field circuit resistance of 2 0, 200 ohms respectively. It is driven at 1000 r.p.m. Calculate the flux per pole in the machine. If the machine has to be run as a motor with the same terminal voltage and drawing 5 amps from the mains, maintaining the same magnetic field, find the speed of the machine.

A d.c. shunt generator has 6 pole, 34 conductors, lap-wound, with terminal voltage of 210 volts delivering 11 amps to the load, has armature and field circuit resistance of 2 0, 200 ohms respectively. It is driven at 1000 r.p.m. Calculate the flux per pole in the machine. If the machine has to be run as a motor with the same terminal voltage and drawing 5 amps from the mains, maintaining the same magnetic field, find the speed of the machine.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 4 pole machine generates 250 volts when operated at 1500 rpm. If the flux per pole is 1.85 x 10°maxwell. The number of armature slots is 45 and the armature winding has two parallel paths. Calculate. a). the total number of armature conductor. b). the number of conductor in each slot c). If the speed of the generator is decrease to 1,350 rpm, what will be the generated voltage if the flux per pole is maintained at the value. d). To what value of flux per pole should the excitation be adjusted if the generated voltage is to remain the same. (Hint: Eav and Eg = lave x ²) ØXP X t
An 6-pole d.c. generator has 290 armature conductors, and a useful flux of 12 mWb per pole. What will be the e.m.f. generated if it is lap- connected and runs at 1010 rpm? What must be the speed at which it is to be driven produce the same e.m.f. if it is wave-wound? Generated voltage speed
A 4-pole generator having wave wound armature winding has 50 slots, each slots containing 20 conductors. What will be the voltage generated machine when driven at 1000 rpm assuming the flux per pole to be 6.0 mWb ?
(a) A 2 pole generator with wave wound armature has 75 slots each having 10 conductors. The flux per pole is 34 mWb. At what speed must the armature rotate to give an induced EMF of 205V. (b) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed
Alternator voltage regulation is ............... % *
A 4 pole generator with wave wound armature has 52 slots each having 22 conductors. The flux per pole is 0.01 Wb. (i) At what speed must the armature rotate to give an induced EMF of 220V is, (ii) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is,
ASAP, answer now please..
Calculate the time taken by the output to swing from +14v to -14v for a 741C op-amp having a slew rate of 0.5V/µs? O a. 70µs O b. 42µs O c. 22µs O d. 56µs
Dc machine.............
A 6 pole DC wave wound generator has 41 armature conductors with Flux per pole is 26 mWb and the e.m.f generated is 79 V, then the speed of machine is ?
(a) A 4-pole generator, with wave wound armature, has 51 slots, each having 24 conductors. The flux per pole is 0.01 weber. At what speed must the armature rotate to give an induced emf of 220 V² ? (b) What will be the voltage developed, if the winding is lap and the armature rotates it the same speed?
Show detailed solution with illustration.