A cylindrical conductor has resistance of R0 = 950 Ω. It has length L, radius of the cross section r, and resistivity ρ. a) If the resistivity was restored to its original value and instead the length of the conductor decreased by a factor of 2, what would the value of the new resistance be, in ohms? b) If the resistivity and length of the conductor were at their original values and the radius of the conductor increased by a factor of 4, what would be the value of the new resistance, in ohms?

A cylindrical conductor has resistance of R0 = 950 Ω. It has length L, radius of the cross section r, and resistivity ρ. a) If the resistivity was restored to its original value and instead the length of the conductor decreased by a factor of 2, what would the value of the new resistance be, in ohms? b) If the resistivity and length of the conductor were at their original values and the radius of the conductor increased by a factor of 4, what would be the value of the new resistance, in ohms?

Related questions

Q: , in units of Ω, of the rod? b) What is the current, in units of miliamperes, in the rod

A: Given:- L=9 m A= 2.5 mm2 ρ=ρ01-x2L2 ρ0=2×10-4 ΩV0=25 V Find:- a) What is the total resistance, in…

Q: As the temperature of a metal rod varies, so does the resistance and the dimensions of the rod. If a…

A: At T=20°, the resistance of the rod is given by R20=ρ20l20A

Q: An electrical circuit contains a capacitor of Z picofarads and a resistor of X ohms. If the…

A: Capacitance (C)= Z pF= Z × 10-¹² F Resistance (R)= X ohms Let after t time the capacitor transfers…

Q: A 60 W lightbulb has a resistance of 240 Ω. At the operating temperature of the tungsten filament,…

Q: Figure 8₁ 9.0 V R₁ 22 2 HH ww R₂ = 1892 83=6.0 V 1 of 1 Part A Determine the magnitudes of the…

Q: You have three resistors R1 = 422 Ohms, R2 = 271 Ohms & R3 = 426 Ohms. What is the maximum…

Q: A battery with emf E and internal resistance r is first connectedto a resistor of resistance R1 = R,…

A: In the first case, the battery with emf E and internal resistance r is connected to a resistance R.…

Q: The density of mobile electrons in copper metal is 8.4 x 1028 m3. Suppose that / 4.7 x 1018…

Q: b) The resistance R of a conductor depends on its shape and physical dimensions and a property of…

A: Part (i)The resistivity of a material depends on its material and the working temperature.Part…

Q: You have four homogeneous wires made of the same material. Each wire has a diameter of 3 mm and a…

Q: As the temperature of a metal rod varies, so does the resistance and the dimensions of the rod. If a…

Q: 2.The figure below shows cross sections through three long conductors of the same length and…

A: Determine the cross-sectional area of conductor A. AA=π(RA2−RB2)AA=π[(3R)2−(2R)2]AA=5πR2

Q: Two resistors of resistance 230 O and 340 O are connected in series (one after the other). A…

A: Rtotal=R1+R2=230 ohm+340 ohm=570 ohm

Q: A cylindrical wire has a radius r and length I. If both r and I are doubled, what happens to the…

A: Given that:A cylindrical wire has a radius r and length l.Both r and l are doubled.

Q: A solar cell generates a potential difference of O.17 V when a 520Q resistor is connected across it,…

A: Given:R1=520Ω∆V1=0.17 VR2=940Ω∆V1=0.25 VA=2.5 cm2=2.5×10-4 m2I=5.1 mW/cm2=5.1×10-310-4=51 W/m2 Let…

Q: Two identical resistors of R0 = 71 Ω are connected head-to-tail. (a) Express the resistance R0 of…

A: a)The relation between resistance, resistivitylength & cross sectional area isRo=ρLA

Q: Part (a) Express the resistance Ro of one of the resistors in terms of the resistivity p, length Z,…

A: When two resistances R1 and R2 are connected in series, the net resistance is given by R=R1+R2 It…

Q: Two capacitors of capacitance 3C and 5C (where C = 0.17 F) are connected in series with a resistor…

Q: The resistance of gold wire used in circuits is usually negligible compared to the components in the…

A: Given: Length,L=47.1cm=47.1×10-2mArea,A=1.7mm2=1.7×10-6m2Resistivity,ρ=2.35×10-8Ωm In an electrical…

Q: A platinum resistance thermometer (PRT) is a transducer which measures temperature 0 by means of…

Question

A cylindrical conductor has resistance of R₀ = 950 Ω. It has length L, radius of the cross section r, and resistivity ρ.

a) If the resistivity was restored to its original value and instead the length of the conductor decreased by a factor of 2, what would the value of the new resistance be, in ohms?

b) If the resistivity and length of the conductor were at their original values and the radius of the conductor increased by a factor of 4, what would be the value of the new resistance, in ohms?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given information

VIEW

Answer

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Ohm’s law states that the voltage drop V across an ideal resistor is linearly proportional to the current I flowing through the resister as in V = IR, where R is the resistance. However, real resistors may not always obey Ohm’s law. Suppose that you performed some very precise experiments to measure the voltage drop and corresponding current for a resistor. The following results suggest a curvilinear relationship rather than the straight line represented by Ohm’s law: I -1.5 -0.5 -0.25 0.25 0.5 1.5 V -982 -166.6 -54 54 166.6 982 Table 2 To quantify this relationship, a curve must be fit to the data. Because of measurement error, regression would typically be the preferred method of curve fitting for analysing such experimental data. However, the smoothness of the relationship, as well as the precision of the experimental methods, suggests that interpolation might be appropriate. By using all the set of values given in table 2, apply Newton Divided…
A capacitor of 7.99 µF is discharged through a resistor of resistance R. The time constant of the discharge is 5.6 space cross times space 10 to the power of negative 3 end exponent s Calculate the value of R.
Two points 0.0001 m apart in a micro-circuit are to be joined by a silver conductor. Determine the area of this conductor if the resistance is not to exceed 0.00002 ohms.
Two capacitors of capacitance 3C and 5C (where C = 0.17 F) are connected in series with a resistor of resistance R = 6.5 Ω. a) How long will it take the amount of charge in the circuit to drop by 75% in seconds? b)
A capacitor with a capacitance of 3.5 μF is initially uncharged. It is connected in series with a switch of negligible resistance, a resistor with a resistance of 19 kΩ, and a battery that has a potential difference of 170 V. What is the charge Q, in microcoulombs, on the capacitor when the current in the resistor equals one half its maximum value.
Consider the circuit shown below, with a battery of emf E = 20. V, and resistors R1 = 2.0 Ω, R2 = 5.0 Ω, R3 = 4.0 Ω, and R4 = 12 Ω. In this problem, give your answers to two significant figures a) What is the equivalent resistance of this set of resistors, in ohms? b) How much current Ibat flows through the battery, in amperes? c) How much current I1 flows through resistor R1, in amperes?
Consider the network of four resistors shown in the diagram, where R1 = 1 Ω, R2 = 5 Ω, R3 =2Ω,andR4 =6Ω. . The resistors are connected to a battery with an emf V. (a) What is the current flowing out of the battery if the emf is 12 V? (B) What is the voltage difference across the resistor R1? (C) What is the rate of Ohmic dissipation for resistor R2?
Consider the following circuit diagram. The potential difference across the battery is 40.0 volts, and it supplies a current of 5.00 amperes to the circuit. There is a current of of 2.70 amperes flowing through R1. Resistor R2 has a resistance of 5.50 ohms. What is the resistance of R3? Answer in ohms to two decimal places, but do not include units in your answer.
If R is the total resistance of three resistors, connected in parallel, with resistances R₁, R₂, R3, then 1/2 = 1/₂+1/2+1/3 R R₁ If the resistances are measured in ohms as R₁ = 64, R₂ = 82, and R3 = 42, with a possible error of 0.5% in each case, estimate the maximum error in the calculated value of R. (Round your answer to three decimal places.) .005 x 22
Resistance, R, is defined using R = V/I where V is the potential across a resistor, and I is thecurrent. R is measured in ohms (Ω), where 1 Ω = 1 V/A. The constant you determined in eachequation should be similar to the resistance of each resistor. However, resistors aremanufactured such that their actual value is within a tolerance. For many common resistors, thetolerance is 5% or 10%. Calculate the range of possible values for each resistor. Does the constant in each equation fit within the appropriate range of values for each resistor? Do the resistors follow Ohm’s law? Base your answer on your experimental data. Slope (V/A) Y-intercept (V) Resistor 10 Ω 9.896V/A 0.0005526V Resistor 51 Ω 50.91V/A 0.01030V Light bulb (first 3 pts) 5.386V/A n/a Light bulb (last 10 pts) 43.26V/A n/a
Resistance depends on the size and shape of a conductor. We expect a long wire to have higher resistance than a short one (everything else being the same) and a thicker wire to have a lower resistance than a thin one. Resistance also depends on the intrinsic property of the conductor called the resistivity. If the resistivity of a particular wire is 21.63x10-8 · m, the wire is 11.12mm in length, and the radius of the diameter of the wire is 1.62m, what is the resistance of the wire in units of Ohms (N)? Note: It is understood that the unit of your answer is in Ohms (N), however do not explicitly include units in your answer. Enter only a number. If you do enter a unit, your answer will be counted wrong.