A cylinder with a bore diameter of 1.5 in and a rod diameter of 0.625 in is to be used in a system with a 10 gpm pump. What are the extension and retraction sneedr?

Q: which is given. What are the x and : coordinates of the bracket's mass cen- ter? (The angle 0 in the…

A: To Find :  The x and z coordinate of the bracket mass . Given :  The total number of hole is n=4 The…

Q: Draw isometric projection of casting, two views (FV and TV) of which are shown in figure in First…

A: Refer the following image for the the required rough sketch of isometric view of the given…

Q: Draw the isometric projection For the Shapes Shown Below, Using Scale (1:1)

A:

Q: 4. The diameter of a circle has endpoints: (2, -3) and (-6, 5). Can you find the coordinates of its…

A: We know that if the endpoint of diameter of circle are p(x1, y2) and q(x2, y2)  Then it's center's…

Q: Determine the moments of inertia of area with respect to centroidal axis parallel to y-axis as shown…

A:

Q: Q. 2 Find the position of centroid with respect to given X and Y axis of shaded portion in the…

A: Given Shaded area To find Centroid

Q: ده ))

A: The mass of each piece is m.

Q: Can you please draw Mohr's circle for the solution above?

A: Given that, σx=350 MPaσy=230 MPaτxy=-480 MPa

Q: find area between line y=-2+x and y=x^(1/2) and x-axis

A:

Q: Find the areas of the parallelograms whose vertices are given in points A(1, 0), B(0, 1), C(-1, 0),…

A:

Q: is it correct?If this is correct, please help me to see the red line or red circle which has the…

A:

Q: Determine the volume flow rate, Q, of air in Figure Q1 (c) assuming that the flow is inviscid and…

A: Stagnation pressure = static pressure + dynamic pressure

Q: Mohr's circle for an element is shown below, each grid square is 20 MPa. The principal plane is: 1…

A:

Q: 1: Determine the resultant and angle for the figure below: l1-400N 30 60 F3-200N F2-300N

A:

Q: Q5: For the below shaded area, calculate kand Kr 130 mm 30 mm 30 mm 40 mm 40 mm

A:

Q: Given the multiview projection of the solid, draw the isometric view. HRP FRP F DA FRP PRP

A: Given the multiview projection of the solid, draw the isometric view.

Q: Please find the centroid and Ixx for the following shapes. Show all work with neat handwriting and…

A:

Q: Question 7 of 10 The purpose of the inclining experiment is to find the: O Metacentric radius. O…

A: The purpose of inclining experiment is to establish the vertical distance of centre of gravity from…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: Can you pls slove this question briefly with hand written notes and diagram

A:

Q: Draw projections of this plane and find its inclination with the HP

A:

Q: 32.м т пу є 0.5 cm 12- 5 ст эт 0.5cm X

A:

Q: Draw the three Views and a section elevation:

A: Required all three views Elevation, Right Hand Side View, Plan and Sectional Elevation are drawn…

Q: For the objects shown in orthographic projection below, construct an isometric Use the box method to…

A: Find Isometric view of the object.

Q: Find area of the shaded part using inventor

A: Find Find the area of the shaded part.

Q: Compute a little more by taking the integralinii) terms up to the 5th order ii) taking the terms up…

A:

Q: 2.5 m

A:

Q: Find Ix for the shape below:

A: To determine: The moment of inertia of the shape about X axis. Image: Consider a image below:

Q: How is the mohrs circle plotted? what values were plotted

A:

Q: 20 30 40. -30 100- Draw the three projections of the following figure 60

A:

Q: for question 1, how did you get the area for the triangle? i dont understand how you got (.15-x)*2

A: The total height of the water level:Length of the base of the traingle:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: I need these three parts answered, if you are unable to answer all three parts please leave it for…

A: 4.The number 81073 denotes the CAGE no. as shown in the print. The CAGE code indicates Commercial…

Q: The opposite figure is composed of a rectangle (b-16.8 , h=8.4 m, density 8 kg/m2) and a triangle…

A:

Q: Draw isometric projection of a cylinder of diameter 30 mm and height 50 mm

A: In isometric projection, the three edges of a solid right angle of an object are shown by means of…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.