A cylinder measuring 3.7 cm wide and 4.5 cm high is filled with gas. The piston is pushed down with a steady force measured to be 36. N piston cylinder gas Calculate the pressure of the gas inside the cylinder. Write your answer in units of kilopascals. Round your answer to 2 significant digits.

Q: Arrange the following molecules in increasing order of: H₂ H₂ H3C H3C H₂ с A CH3 CH3 H3C D H3C CH 3…

A:

Q: When using a TD pipet, one should not O blow or shake out the remaining liquid O place the meniscus…

A: Given that : We have to identify that while using TD pipet one should not :

Q: true

A: Answer : true . Viscosity is the property of liquid to resist the flow of liquid.

Q: High chemical potential results to stability of a particular phase.   True False

A: The phase diagram represents the different phases of the substance and the pressure and temperature…

Q: Justify that Glass is an insulating material.

A: Conducting material : The materials which conduct electricity when electricity is passed through it,…

Q: Root cause of energy bands in solids.

A: Solids have been classified into 3 types: conductors, semiconductors and insulators. Conductors are…

Q: What type of defect can arise when a solid is heated?

A: All matter can exist in different physical states; solid, liquid and gases. Solid is well known…

Q: How do you weigh hygroscopic solids? Give three examples of hygroscopic solids.

A: Hygroscopic property can be defined as the ability of a matter to absorb water from air. We have…

Q: are glasses that have no sharp melting temperature, but rather harden and develop resistance to…

A: Glass is a inorganic solid which is may be transperant or translucent, but brittle in nature.

Q: A loose material has a:   a.Low spring constant.   b.Spring constant of any value.   c.High spring…

A: A material can be stiff or loose in nature. Hooke's law determines a relation between the spring…

Q: If the tube is packed with too much material, the melting point you determine may be

A: Melting point : The temperature at which a solid melts to form liquid is called it's melting point.

Q: it is Intermolecular attraction between two permanent dipoles _________

A: The strongest type of intermolecular bond is hydrogen bonding. When a hydrogen atom is covalently…

Q: 7)Viscosity inscresses with increasing pressure true or false

A: Viscosity is the resistance to the flow of a liquid and gases. It is generally measured in a unit…

Q: The use of Metal on Metal bearing systems are under increasing scrutiny by Medical Regulatory…

A: A question based on introduction to chemistry. A question about the impact of the use of metal on…

Q: describes the viscosity of the emulsions?

A: High zero-shear viscosities can prolong product shelf life by inhibiting creaming processes and…

Q: Consider the effect of intermolecular forces on the vapor pressure (vp), boiling point (bp), and…

A: As the strength of intermolecular forces decreases. What  effects occur on the  Changing vapor…

Q: The property of liquids that explains the formation of water droplets on a polished surface is…

A: Given that, The property of liquids that explains the formation of water droplets on a polished…

Q: TRUE OR FALSE Melting Point should be taken on dry solids only.

A: Yes it is true melting point should be taken of dry solid only . because if  it contains moisture…

Q: Young's Modulus is an example of ______ property.

A: Given: Young's Modulus is an example of ______ property.

Q: - Camper between Sorption and Surface tension

A:

Q: Make a descriptive introduction about heating curve of water.

A: A heating curve graphically addresses the stage advances that a substance goes through as hotness is…

Q: Which statements about viscosity are true? i. Viscosity increases as temperature decreases. ii.…

A: The viscosity of a liquid is defined as the internal friction which opposes the relative motion of…

Q: Briefly discuss the defects in solids.

A: There are basically two types of Defects in Solids:- a) Point Defects   - The defects which arise…

Q: Q6. Read both statements and choose the correct answer. I Yeild presim hetter Commers Statement A:…

A: Introduction: A tableting excipient is a substance that is added to the tablet to improve its…

Q: Are there any alternatives for a rotary evaporator?

A: Rotary evaporator is an equipment used in chemical laboratories to separate the solvents and the…

Q: Please give proper answer List the two main kinds of line defects occurring in solid materials…

A:

Q: The cooling rate affects the size of the crystals.

A: Solution :   Crystallization is a process of formation of a solid crystal that is formed by…

Q: The pressure that vapors apply on the surface of the liquid at equilibrium is called

A: On the surface of a liquid some of the liquid vapours are present.

Q: Consider a metal single crystal oriented such that the normal to the slip plane and the slip…

A: Given: φ = 43.1°, λ = 47.9° critical resolved shear stress = 20.7 MPa and  applied tensile stress =…

Q: Why Clausius–Clapeyron equation imporant?

A: The Clausius-Clapeyron equation refers to the relationship between temperature and pressure in…

Q: oxygen tank to porduce steam

A: In this question we have to explain that how to calculate the heating surface of an oxygen tank also…

Q: Of the following, ________ is endothermic. Group of answer choices condensation all these processes…

A: Condensation , deposition and crystallization is exothermic process.