A counterweight of mass m = 4.00 kg is attached to a light cord that is wound around a pulley as in the figure. The pulley is a thin hoop of radius R = 8.00 cm and mass M = 2.00 kg. The spokes have negligible mass. (a) What is the magnitude of the net torque on the system about the axle of the pulley? (b) When the counterweight has a speed v, the pulley has an angular speed ω = v/R. Determine the magnitude of the total angular momentum of the system about the axle of the pulley. (c) Using your result from part (b) and (see image for formula), calculate the acceleration of the counterweight.

A counterweight of mass m = 4.00 kg is attached to a light cord that is wound around a pulley as in the figure. The pulley is a thin hoop of radius R = 8.00 cm and mass M = 2.00 kg. The spokes have negligible mass. (a) What is the magnitude of the net torque on the system about the axle of the pulley? (b) When the counterweight has a speed v, the pulley has an angular speed ω = v/R. Determine the magnitude of the total angular momentum of the system about the axle of the pulley. (c) Using your result from part (b) and (see image for formula), calculate the acceleration of the counterweight.

Similar questions

The wheels of a wagon can be approximated as the combination of a thin outer hoop, of radius ?h=0.421 m and mass 5.46 kg, and two thin crossed rods of mass 7.37 kg each. A farmer would like to replace his wheels with uniform disks ?d=0.0588 mthick, made out of a material with a density of 5990 kg per cubic meter. If the new wheel is to have the same moment of inertia about its center as the old wheel about its center, what should the radius of the disk be?
A combination of an applied force and a frictional force produce a constant total torque of 32 N-m on a wheel rotating about a fixed axis. This combined force acts for 10 s, during which the wheel’s angular speed increases from 0 to 8 rad/s. Find the moment of inertia of the wheel.
A torque of 100 Nm rotates the flywheel 200 rad in 10 s starting from rest. The moment of inertia of the wheel is?
In the figure, two 6.20 kg blocks are connected by a massless string over a pulley of radius 2.40 cm and ro- tational inertia 7.40×10-4 kgcdotm?. The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is relea- sed from rest, the pulley turns through 0.650 rad in 91.0 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acce- leration, (c) string tension Tı, and (d) string tension T2?
A solid ssphere of radius 25cm & mass 25kg ro fater about an axis through its center. Calculate its moment of inertia of its angulal velocity changes from 2 rad/s to 12 rads in 5 second. Also calculate torque applied?
If a torque of 20 N.m is applied to a wheel (I wheel = m R 2 ) radius 0.60 m. If the wheel accelerates at a rate of 2 rad/s 2, what is the mass of the disk?
A solid cylinder with mass mm and radius rr rolls without slipping down an incline that makes a 29.5° with the horizontal. What is the acceleration of the cylinder?
A constant torque of 17.6N m is applied to a grindstone for which the moment of inertia is 0.151kg · m2. Find the angular speed after the grindstone has made 14rev. Assume the grindstone starts from rest.
spokes Ave negligile mass. (o) What is the net torque on the rystem about the axie of the pullew? magnitude \[ N=m \] dicectien2a+m)2
A stone is suspended from the free end of a wire that is wrapped aroundthe outer of a pulley as shown. The pulley is a solid cylinder with mass 10.0 kgand radius 30.0 cm. You measure that the stone travels 12.6 m in the first 3.00s starting from rest. What is (a) the tension in the wire and (b) the mass of thestone?
Don't use chat gpt It Chatgpt means downvote
2. A 50.0-kg block and a 100-kg block are connected by a string as shown in the figure below. The pulley is frictionless and of negligible mass. The coefficient of kinetic friction between the 50.0-kg block and the incline is uk = 0.250. 50.0 kg B) 100 kg V 37.0° (a) B, what is its speed after it has traveled a distance of 20.0 m to point B. (Assume that the 100-kg block does not reach the ground.) Assuming that the 50.0-kg block starts from rest at point A to point