Completely solve and box the final answer. Write legibly 6. A counterflow heat exchanger is designed to heat fuel oil from 32.5ºC to 94.7ºC. The hot flue gas enters at 174.3ºC and leaves at 120.8ºC. Calculate the log mean temperature difference.

Completely solve and box the final answer. Write legibly 6. A counterflow heat exchanger is designed to heat fuel oil from 32.5ºC to 94.7ºC. The hot flue gas enters at 174.3ºC and leaves at 120.8ºC. Calculate the log mean temperature difference.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.36P

See similar textbooks

Related questions

Q: 1. 400,000 Ibm/hr of 270°F water is to be heated to 370°F by condensing saturated 390°F steam. (The…

A: Given :- Number of tube passes : 4 Change of temperature : 270F-370F Velocity of fluid : 5ft/sec

Q: Benzene flowing at a rate of 10000 lb/h is to be heated from 60 F to 120 F in a double pipe heat…

A: To design the double pipe heat exchanger, we need to determine the heat transfer area, overall heat…

Q: Example 25.9 A refrigeration cycle uses Freon-12 as the working fluid. The temperature of the…

Q: A refrigerant 22 vapor compression system includes a liquid-to-suction heat exchanger in the system.…

A: (a) Draw the T-s diagram for the cycle without the heat exchanger. From the properties table for…

Q: 1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle')…

A: Given data: Mass flow rate (m) =25 kg/s Write thermal property value at the corresponding points…

Q: A counter-flow bank of boiler tubes has a total area of 900 sq ft and its overall efficiency of heat…

Q: The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam…

Q: 02. The Li-Br water absorption cycle with heat exchanger between absorber and generator operate at…

A: Given that, Generator Temperature, TG=100 °C=373 K,Evaporator Temperature, TE=10 °C=283 K,Absorber…

Q: A shell-and-tube heat exchanger operates with two shell passes and four tube passes. The shell fluid…

A: Write the given data. For ethylene glycol,Thi=140 °CTho=80 °Cm˙h=4500 kg/hch=2742 J/kg°CFor…

Q: A heating plant for a large medical campus requires 5506 MBH (1MBH \= 1,000,000 btuh) of heating…

A: Given:Let's first convert the heating capacity from MBH to Btuh:Simplify the heating capacity as…

Q: Question 1 Water enters the heat exchanger at 20°C and leaves at 35° What is the log mean…

Q: Steam is generated at 6.10 MPa and 450OC and condensation occurs at 170 kPa. (a)For a Rankine engine…

A: Given: P1=6.10 MPaT1=450°CP2=170 KPaP=35 MW

Q: Draw the Temperature & compute the LMTD for CO-CURRENT & COUNTER-CURRENT flow heat exchanger. Water…

A: Steam condenser saturation temperature = 40 °C. Inlet condition of cooling water=20 °C outlet…

Q: 5. Sketch a Rankine cycle on T-s diagram and derive the thermal efficiency for a rankine cycle from…

Q: 5. Determine the LMTD for heat exchanger equipment that has a condensing temperature of 100ºF. The…

Q: A liquid to liquid counterflow heat exchanger is used to heat a cold fluid from 130°F to 320°F.…

Q: 20 g (d) TOIq (s) A skell-and-tube exchanger with two tube passes is used to heat ethanol from 60°F…

A: Shell and Tube Heat Exchanger is most normal sort of hotness exchanger in petroleum treatment…

Q: A surface condenser is designed to handle 10000 kg of steam per hour. The steam enters at 0.08 bar…

A: The answer is -

Q: Completely solve and box the final answer. Write legibly Diesel flows at the rate of 3 kg/sec…

Q: 1ge gas consists of a one-shell-pass, one-tube-pass he exchanger. The oil (c, = 320 F flowing…

Q: The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam…

Q: 5. Steam is generated at 6.10 MPa and 4500C and condensation occurs at 170 kPa. (a)For a Rankine…

Q: The clean U for an exchanger is 770 BTU/(hr 0 F ft2). Its tube area is 550 ft2. After operating…

A: Heat exchanger: It is a system used which is used to transfer heat between two or more than fluids.…

Q: 1) Steam boiler is to generate saturated steam at 800 kPa abs from water at 70 C. Flue gas from…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A single cylinder petrol engine works on the Otto cycle and draws in air at 1.01 bar and 22°C. The…

Q: 1 Steam is generated at 4.20 MPa and 460°C and condensation occurs at 0.10SMPa. a For a rankine…

A: Given data Steam is generated at 4.20 MPa and 460°C and condensation occurs at 0.105MPa. To…

Q: The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam…

Q: Please find the highest thermal efficiency possible, while remaining within the boundaries. What…

Q: The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam…

Q: Double-pipe heat exchangersare used in many industries because of their low design and maintenance…

Q: he condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam…

Q: Milk at 40 ° C with a specific heat of 3.85 kj / kg K will be pasteurized at 75 ° C by using…

A: Consider the diagram shown below for the parallel flow heat exchanger. The heat lost by the 1 kg of…

Concept explainers

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.

Question

Completely solve and box the final answer. Write legibly

6. A counterflow heat exchanger is designed to heat fuel oil from 32.5ºC to 94.7ºC. The hot flue gas enters at 174.3ºC and leaves at 120.8ºC. Calculate the log mean temperature difference.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Completely solve and box the final answer. Write legibly Diesel flows at the rate of 3 kg/sec through a double pipe counter-flow heat exchanger. Diesel is heated from 60°C to 75°C by a water (Cp = 4.187 kJ/kg-K) flowing through the tube. The specific heat of the diesel is 1.780 kJ/kg-K. The water enters at 115°C and leaves at 70°C. The overall heat transfer coefficient is 340 W/m2-K. Calculate the heat exchanger area and the rate of heat transfer.
Alert for not submit AI generated answer. I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image and hand writing
A counter-flow heat exchanger is designed to heat fuel from 45°C to 100°C while the heating fluid enters at 150°C and leaves at 115°C. Calculate the arithmetic mean temperature difference in °C. Round your answer to 2 decimal places.
Solution with matching schematic diagram pls
Please as soon as possible
Question 1 Water enters the heat exchanger at 20°C and leaves at 35° What is the log mean temperature difference if the hot fluid enters and leaves at 45°C? 4 Next ▸
Completely solve and box the final answers. Write legibly. Please don't copy from other platforms, the answer is already provided (highlighted), please please write legibly.
An air-cooled condenser has an expected U value of 30 based on the air-side area. The m²-k condenser is to transfer 60 kW with an airflow rate of 15 kg/s entering at 35°C. If the condensing temperature is to be 48°C, what is the required air-side area? Recall Cp,air = 1.0- kg-K kJ
1. 400,000 Ibm/hr of 270°F water is to be heated to 370°F by condensing saturated 390°F steam. (The steam does not sub cool upon condensing). Your job is to design the heat exchanger. The following parameters represent constraint your design. number of tube passes 4 tube fluid water being heated number of shell pass shell fluid steam being cooled U (based on outside tube area) 700 BTU/hr – ft² – °F 1 in tube outside diameter tube wall thickness 1/16 in bulk tube fluid velocity 5 ft/s (a) How many tubes are required per pass? (b) How many tubes are required total? (c) Allowing 3 ft for headers and flanges, how long should the exchanger be?
Im struggling and I have exam tomorrow! Help idk how to do it
Kindly solve fast
Completely solve and box the final answer. Write legibly 5. Determine the LMTD for heat exchanger equipment that has a condensing temperature of 100ºF. The air enters the condenser at 52ºF and leaves at 78ºF.