A copper bar (2.00 cm by 2.00 cm and 10.0 cm long) is welded end to end to a brass bar of the same dimensions. The free end of the copper bar is placed in a steam bath and the free end of the brass bar is placed in an ice bath. If the system is at steady state condition and that both bars are properly insulated. (Given the thermal conductivity of copper is 390 W m1°C-1 and he thermal conductivity for brass is 110 W m1°C1) a.) What is the temperature T at the interface of the copper-brass bar? b.) How much thermal energy flows through the bar per minute?

A copper bar (2.00 cm by 2.00 cm and 10.0 cm long) is welded end to end to a brass bar of the same dimensions. The free end of the copper bar is placed in a steam bath and the free end of the brass bar is placed in an ice bath. If the system is at steady state condition and that both bars are properly insulated. (Given the thermal conductivity of copper is 390 W m1°C-1 and he thermal conductivity for brass is 110 W m1°C1) a.) What is the temperature T at the interface of the copper-brass bar? b.) How much thermal energy flows through the bar per minute?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
At a temperature of 21.4°C the hole in a steel plate has an area of 8.80 x 10- m2. You heat the plate until the area of the hole increases to 8.97 x 10- m2, which allows a steel rod to just slip through this hole. What is the final temperature of the plate? The coefficient of linear expansion of steel is 12 × 10-0/°C.
A furnace wall consists of 2 ft of brick . The brick has athermal conductivity of 0.6 Btu/ hr sq ft ( ° F /ft), a specific heat of0.2 Btu/ lb ° F, and a density of 110 lb/cu ft. The temperature atthe inside surface of the wall is 1100 ° F , and at the outside surface,200 ° F .(a) Calculate the thermal diffusivity of the brick .(b) Calculate the heat loss per hour through a wall 10 ft high and10 ft long(c ) Calculate
You are designing a 3m x 3m floor with radiant heating. The floor has 12 parallel pex pipes (k = 40 W/mK) of L = 3m, OD = 25mm and ID = 20mm. Hot water (TInfintiy 1 = 90oC, h = 200 W/m2K) runs through the pipes continuously. The surface below the pipes is perfectly insulated. Above the pipes, there is a 3mm layer of bonding material (? = 12 W/mK) and a 9mm layer of tile (k = 2 W/mK). Above the tile, there is air (TInfinity 2 = 25oC, h = 20 W/m2K). Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), Hint: Assume that the “layer” of pipe starts at the center point (e.g. for conduction purposes, the pipe is OD divided by 2 thick). For convection, consider the entire pipe surface. a) What is the total heat rate entering the room above the floor? b) What is the temperature of the top of the tile?
Heat Transfer - Fins See image attached.
Consider the following cases: Case 1: A rod with specified surface temperature. Case 2: A rod with specified surface temperature with heat generation. Case 3: A rod with specified surface temperature with variable thermal conductivity k=k(1+BT), ß: is constant. The quadratic temperature profile T(r)= f(r) will be in:
heat transfer course Consider a large plate as given in the figure below. The thermal conductivity and thickness of the plate are 0,55 W/m.K and 3,915 mm. What is the surface temperature (Ts) of the plate in K for given properties?
Please solve Correctly as Answer is already given. Don't Copy
A brass plug is to be placed in a ring made of iron. At 20°C, the diameter of the plug is 8.755 cm and that of the inside of the ring is 8.741 cm. They must both be brought to what common temperature in order to fit? Given : Required : Illustration: Solution: final answer:
What is(roughness)? what is its effect on heat transfer? Write one or two pages providing schemes or illustration for more demonstration.
The temperature distribution in a wall (conductivity k=6-W/m2C, thickness L=10-cm) is given as T(x)=(-454 x2+53 x+ 17) (in °C) Assuming unit wall surface area, calculate the rate of heat loss from both sides of the wall in Watt.
Kindly answer this question, T= 30 degrees