A continuous-time system is designed to have impulse response of h(t) = 2e¯4¹u(t) For an input signal x(t) = 2 + cos(951t) − cos(4ñt +7). 1. find the output y(t) after passing x(t) through the system, you may need to round your results to four decimal places. 2. plot the frequency spectrum of y(t), please include the complex amplitudes in your drawing.

A continuous-time system is designed to have impulse response of h(t) = 2e¯4¹u(t) For an input signal x(t) = 2 + cos(951t) − cos(4ñt +7). 1. find the output y(t) after passing x(t) through the system, you may need to round your results to four decimal places. 2. plot the frequency spectrum of y(t), please include the complex amplitudes in your drawing.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An ideal boost converter is utilized in designing a PV storage system. The boost converter is operating at the boundary layer between the continuos conduction mode and discontinuous conduction mode. Design the mathematical model of the switching frequency for this boost converter in terms of load, duty cycle and inductance under the above operating conditions.
Indicate which of the following signals can be sampled without any loss ofinformation? For signals that can be sampled properly, determine the minimum samplingrate that can be used.
Fine the time domain waveforms of i(t). R1 i(t) 30 N + R2 Vs(t): = 110 cos(2760t+0°) V 60 N 65 μF
Given the discrete-time sinusoid:x(n)=2cos(nπ/2)+sin(3nπ/4)Ignoring the effects of aliasing, if this was due to sleeping rate Fs = 79 Hz. What are the frequencies of the continuous-time cosine and sine functions?
Dynamical Systems c. An analog signal is distinguished by *a(t) = cos(200nt)+ sin(400nt) for the signal ya(t) = x(3t+ 4), for this signal, prove that the Nyquist rate and Interval can be determined.
For the signal f (t) = 2 cos²(t) + sin(4t) 1) Determine if the signal f (t) is a periodic signal or not. If it is periodic, find its period. 2) Determine if the signal f (t) is a power or an energy signal. Prove that. 3) Draw the amplitude spectrum of the signal f(t). 4) Draw two-sided magnitude spectrum of the signal f (t). 5) Calculate the power of the signal using frequency domain.
Question 3 Consider the two signals c₁ (t) = 4 cos(50000πt) and c₂ (t) = 4 sin(50000t). The real and the imaginary parts of the spectrum of two signals, m₁(t) and m₂(t), are shown in the following figure. M₁(f) M₂(f) Re Im -5000 -5000 10 0 5000 f-> 5000 f-> -5000 M₂(f) -5000 10 5000 f-> 5000 fƒ→ 1) Draw the real and the imaginary parts of the spectrum of z(t) = m₁(t)c₁(t) + m₂(t)c₂(t). 2) Draw the real and the imaginary parts of the spectrum of w(t) = m₁(t)c₁(t) — m₂(t)c₂(t). 3) If z(t) is multiplied by c₂(t), then integrated (or equivalently, passed through a LPF), what will be the output signal? 4) If w(t) is multiplied by c₂(t), then integrated (or equivalently, passed through a LPF), what will be the output signal?
The signal x ( t ) is made up of a sum-of-sinusoids as follows: x( t ) = 1.2cos(168π + 0.05) − 2.5sin(588π t) + 5cos(420π t+π/3) + 0.5cos(1092 π t−0.4π) what is the fundamental frequency [f0] Hz of x(t)
When a 10V 5 Hz sinusoidal signal is applied to the input of the given system, what is the amplitude of the signal to be obtained from the output?