A continuous-time signal z(t) = 4,1sin(920nt)+2.5cos(486t) is impulse-train sampled with sampling functionp(t) = E- 3(t – nT,) for T, = 1ns. What is the valur of the sarmpled signal r, (t) = r(t)p(t) for t = 347.6 ms?Specify your answer to three decimal places.

Answered: Image /qna-images/answer/3b44b6fb-8b25-4a74-89c0-45d59c34c203.jpg

A continuous-time signal z(t) = 4,1sin(920nt)+2.5cos(486t) is impulse-train sampled with sampling function p(t) = E- 3(t – nT,) for T, = 1ns. What is the value of the sarmpled signal r, (t) = r(t)p(t) for t = 347.6 ms? Specify your answer to three decimal places. %3D

A continuous-time signal z(t) = 4,1sin(920nt)+2.5cos(486t) is impulse-train sampled with sampling function p(t) = E- 3(t – nT,) for T, = 1ns. What is the value of the sarmpled signal r, (t) = r(t)p(t) for t = 347.6 ms? Specify your answer to three decimal places. %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a piano. When we press and hold a key, the volume of the note is measured to be y(t) = e-t – e-10t. Determine the piano's transfer function from key depression to volume. What are the implications of the zero in the transfer function?
T1 (t) and r2 (t) are two given signals. r1 (t) is band-limited to 500 Hz and r2 (t) is bandlimited to 2.5 kHz. 1. f. Hz 500 O 500 1 f, Hz -2500 2500 QUESTION 2 These signals are multiplexed by impulse-sampling them at a rate T and combining the samples as shown in the figure. The multiplexer output is given by y (t) = 1 (t) E 5(t – nT') + #2 (t) E 6 (t- nT –5) n=-00 n=-00 (a) demultiplexing? What is the minimum value of T which makes it possible for us to recover the signals after (b) Plot the Fourier transform of r1 (t) E 8 (t – nT'). n=-00 NOTE: F (# (t)] = / (t) e-jut dt 2n FE 8 (t – nT) ) = E 6 (w - kuo) k=-00
(a) The analog signal x(t) = sin(60rt) is sampled at 20 Hz. Derive and write down an expression for the sampled signal r[n]. What is the Nyquist frequency for this r(t)?
The continuous time signal *(t) = cos(4000m) is sample with a sampling period T to obtain a discrete time signal. TUR 3 Determine a choice for T consistent with this information. x[n] = cos
A continuous time signal is given by: x(t) = A cos(8000t) cos (2000nt) %3D The signal is sampled with a sample period of 3 x 10-4 seconds. Can we recover the signal from the sampled version using an appropriate low pass filter?
Find the transfer function of the graphical output given to you by the customer, shown below and you are asked to determine the number transfer function. Your answer should be stated as Y(s)/R(s) knowing the canonical 2nd order form. You can read the Precent Overshoot, the time to peak (Tp), the settling time, Ts, and the Mp, maximum amount of overshoot. Assume that there is a Unit step applied to this second order system. You must show all work. Final Answer in Box must follow the standard form, shown for your help. P.O.= 100e-<#//IR G (s) = g2+2(Wn&+w 1.4 T, : 1.2 1.0 4 T, = 47 = 0.8 0.6 0.4 Mp = e-5//1-g2 0.2 니5 Time (s) 2 3. Response
Find out, if any, the following for every transfer function above:1. Open Loop poles and zeros2. Root locus segment on the real axis3. Find break-away and break-in points4. Asymptote line5. ??-axis crossing.6. ????????? and ??????al
Question 7: The signal x(t) = =2 cos(60nt) +3 cos(100nt) is sampled at S = 120 Hz. a. Find the minimum number N of samples necessary to prevent leakage. b. Find the frequency spacing (resolution). C. Determine the amplitude values of the DFT.
sample per sece 4. Consider the signal x(t) = 10 – 20 cos (4nt +) + sin (1 where t is in seconds. Find the Nyquist rate of x(t) and the discrete-time signal x[n] obtained when sampling x(t) at twice the Nyquist rate. What is x[1]?
Determine the Nyquist rate of a signal whose frequency spectrum is given by ¤(f) = r(f) – 2r(f – 1000) + 2r(f – 3000) – r(f – 4000), where r(f) is the unit ramp function in the frequency domain. O a. 6 kHz O b. 12 kHz O c. 3 kHz O d. 2 kHz O e. 4 kHz Of. 8 kHz A sampling process uses a sampling rate of fg. Determine which of the following input signal frequencies will not be aliased to 0.4f, if it undergoes the said process. О а. 1.6f, оБ. 2.4f. Ос. 1.4f. O d. 1.8f, A continuous-time signal is composed of in-phase sinusoids with periods of 1 ms, 2 ms, and 4 ms. Determine the maximum sampling period allowed to avoid aliasing. O a. 0.4 ms O b. 0.5 ms Oc. 0.2 ms O d. 0.1 ms O e. 0.8 ms Of. 1.0 ms
Theoretically, The slowest sampling frequency given that would avoid aliasing the waveform y(t) = 5sin(12πt) + 8cos(24πt) is: a. 12 samples/sec. b. 16 samples/sec. c. 24 samples/sec. d. 24π samples/sec. e. 48π samples/sec.
A continuous-time LZD system has a zero at ?1 = −1 and ?1 = −1.732 + 1.414? and It has two poles at ?2 = −1.732 − 1.414?. The transfer function of the system and the impulse Calculate the answer.