BCR: Points: SHOW ALL WORK AND FORMULAS TO GET MAXIMUM POINTS1. A construction crew lifts approximately 400 Ib. of material several times during a day from aflatbed truck to a 25 ft. rooftop. A block and tackle system with 75 lb. of effort force isdesigned to lift the materials. a). What is the displacement(distance).by the effort force?b). What is the Ideal Mechanical Advantage of the system?2. A/e nut driver with a 1% inch diameter handle is used to install a % 24 UNC 2B machinescrew into a robotic motor. What is the mechanical advantage gained in the system?3. A gardener uses a wheelbarrow to carry a bag of mulch (decaying leaves, bark and compost)that weighs 150 lbs. and requires 60 Ibs. of effort. The distance from the wheel's axle to theeffort is 8 feet.a). What is the Actual Mechanical Advantage of the Wheelbarrow?b). What is the distance from the Wheel's axle to the Load?

Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…

A construction crew lifts approximately 400 Ib. of material several times during a day from a flatbed truck to a 25 ft. rooftop. A block and tackle system with 75 Ib. of effort force is designed to lift the materials. a). What is the displacement(distance).by the effort force? b). What is the Ideal Mechanical Advantage of the system?

A construction crew lifts approximately 400 Ib. of material several times during a day from a flatbed truck to a 25 ft. rooftop. A block and tackle system with 75 Ib. of effort force is designed to lift the materials. a). What is the displacement(distance).by the effort force? b). What is the Ideal Mechanical Advantage of the system?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.) A tank has two rooms separated by a membrane. Room A has 1 kg of air and a volume of 0.5 m3; room B has 0.75 m3 of air with density of 0.8 kg/m3. The two rooms on the tank makes indicates what type of system? a.)Control mass b.) Control volume c.) Isolated system 2.) A hydraulic lift has a maximum fluid pressure of 500 kPa. What should the piston cylinder diameter be to lift a mass of 850 kg. a.) 16.677 m^2 b.) 0.0017 m^2 c.) 0.017 m^2 d.) 1.7 m^2
QUESTION 1 (Simple machines) A hoisting engine lifts a 450 kg bucket containing 5,5 m3 broken ore with a density of 1,6 t/m3 a height of 1 500 m in three minutes. The power supplied to the engine (motor) is 850 kW. Calculate: a) work output b) power output c) efficiency of the hoist
2
Problem 1 (10 points) A robot with a weight of 1000 N on Mars was used for exploration. a Determine the mass of the robot, in kg, or Mars where the acceleration of gravity is 3.73 m/s?. b. What is the robot’s mass on Earth where the acceleration of gravity is 9.81 m/s².
1
A free hanging system of 5 kg weight, and 6 kg weight, tied together with a 4 kg rope is pulled upwards with a force of 300 N. A) what is the acceleration of the system? B) what is the tension of the system? C) what is the tension from the middle of the rope ?
17. A pilot of mass m executes a vertical dive then follows a semi-circular arc until it is going straight up, as shown. What is the net force acting on the pilot at the lowest point? A) less than mg, and pointing up. B) more than mg, and pointing up. C) less than mg, and pointing down. D) more than mg, and pointing down.
Solve it correctly please. I will rate accordingly. SOLVE a,b,c
In machine design we usually compare the equivalent stress of the component with the: a) Allowable stress b) Machine stress c) Force d) Moment e) Torque
A winch mechanism with a handle length of 30 cm and a drum diameter of 8 cm isused to lift a 45 kg load.a. What is the VR of the winch?b. If 73.5 N of force is required to lift the load, what is the MA?c. What is the mechanical efficiency of the winch?d. How many turns will be required to lift the weight 0.85 meters?
Hooke's Law defines the stress-strain relationship for an elastic material: s=Ee, where E= . A)The strain of the material at yield B)The percent elongation at failure C) A constant neutralization reducing the units to zero D) a constant proportionality called the modulus of elasticity
Company manufactures four types of furniture A, super A, B, super B. Furniture A requires (12 ft') of wood and requires (10 ft) of wood. Wood cost is (13 Dinar per one ft). Wood available is (40000 ft). It takes (4 hours) to manufacture A and (2 hours) to manufacture B. More (2.5 hours) need to change A into super A and more (3 hours) to change B into super B. A total of (5000 hours) are available. All furniture can be sold at the following price; A for 90 Dinar, super A 120 Dinar, B for 50 Dinar and super A for 70 Dinar. Formulate an LPM will maximize the profit from manufacturing these four furniture.