A consolidated-undrained test on a normally consolidate clay yield the following results: Confining Pressure = 165 KPa; Deviator Stress 189 KPa: Pore Pressure = 73 KPa. = Calculate the normal stress at the failure plane at drained condition in KPa.

Q: What is the measurement benchmark

A: The given questions asks about the measurement of benchmark.

Q: What is wrong with the picture at right?" (<25 words) YES! Safel NOI Unsafel

A: A picture including of two images where different cases of cylinders were given.

Q: I need this answer handwritten mention question number also and please on white page I'll UPVOTE for…

A: Solution: The given problem is symetrical section with symmetrical loading: Hence it is enough to…

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK Metal…

A: It comes under Engineering Drawing, also known as Engineering Graphics.  For Mechanical Engineering,…

Q: Please answer problem 4 and problem 5 please

A: Solution: Problem 4: Let L = a x b ∑Mc=0 RAa+b-Pb=0RA=Pba+b=PbL

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: In the MIPS instruction "jr $1", what information does register $1 contain?     the address of the…

A:

Q: What is the most common scale used for temperature

A: The Celsius and fahrenheit scale is used most commonly used.. Kelvin scale is primarily used in…

Q: This is incorrect, please redo it, I have attached what the correct answers are supposed to be S

A: For a given soil profile, there is an upward seepage occurring. The velocity of the upward flow, v =…

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS &amp; GNSS surveys.

Q: Q1) The following figure shows the distribution of 11 spot heights with a regular 25 m spacing…

A: The method to be used is triangles method. So the figure which has squares of size 25m×25m should be…

Q: Convert 24 inches to feet.

A:

Q: C ㅏ -80- 99 20 Dimensions in mm Help me to get Ix and ly at Neutral axis. Kindly provide Handwritten…

A:

Q: A. WATER LINES, PIPES, CONNECTIONS AND FIXTURES  B.  SEWER LINES, PIPES, CONNECTIONS AND FIXTURES…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Convert 1600 mils into equivalent value in grads O 90 degrees O 180 degrees O 270 degrees

A: To convert mils to degree

Q: can you reorganize this please? Its a bit confusing to read and understand

A: Given data ,  water content = 45% The density of the solid particles  = 2500 kg/m3   To find out the…

Q: 400 N DY 2 m A 300 N 2 m B 250 N 200 N

A:

Q: What are Line of Balance Charts?

A: A line of balance chart is a graphical report of the schedule of projects that uses progression…

Q: i need all parts of question on the right hand corner solve I STATED FILL IN THE BLANKS.

A: Only 3 subparts can be answered at a time according to guildlines. Please resubmit the question…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.