a: considering the unity feedback system of fig. ,provethe settling time of the resulting second order system for2% tolerance band will be 3.33 sec.?Rb: Obtain the unit-impulse response of a unity feedbackcontrol system whose open loop transfer function is :G(s) =$+19s(s+ 2.4)

Answered: Image /qna-images/answer/4a3065f1-99c1-48c6-94e1-86c4ac046727.jpg

Answered: a: considering the unity feedback…

a: considering the unity feedback system of fig. ,prove the settling time of the resulting second order system for 2% tolerance band will be 3.33 sec.? 9 s(s+2.4)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem @ An altemator on open F6oVt 36O volts fied current is 3.6 amp. Neglacting saturation, determine when 'the freguency n circuit generades at GOHZ nhen the the open circuit is' 4042 to omp and field current is 2.4 amps.
Set up the opamp circuit that performs the following operation. Plot the outputs that appear in the processes for 20 ms. The feedback resistance will be taken as 10kΩ for all circuits. The supply voltage of the opamps that perform the first three operations is ±8 V. The supply voltage of the opamp or opamps in the post-process is ±5 V. In addition, the AC signals given from the inputs have a frequency of 100 Hz. I would be very happy if you could be quick :)
Q.7 Rf(20kn~4okr) slew rate of OP-AMP is 2/usec. and must not be'exceeded. Input voltage Uin is a ramP, as shown. Rfis variable.It varies |from 20k to 40 kr. whạt should he the the highesvalye uf V, that wiill not violate the slew rate? 10kr 30 →t(usec) 20 A 4V B) 6V D 7V E 3 V
A. An inverting Amplifier with a real Op-Amp that has a gain time of 0.001ms and Vcc = ±20 V find the following: 1. Circuit bandwidth? 2. For Vin = 10 sin wt volt, sketch the output waveform for the gain ratio of 15 case.
Given in the figure is a two-stage amplifier design that employs negative feedback. Answer the following questions. Use the notation (R1 + R2 + ... + Rn) for series resistors and (R1 || R2 || ... || Rn) for parallel resistors for clarity and ease. Assume that the transistors are already biased properly in the saturation region and ro1 = ro2 → ∞. Also assume that the capacitors have infinite capacitance. 1.) Find the expression for the open loop gain Av 2.) Derive the resistance Rin which is the resistance that can be seen at the input port of the amplifier
Urgent
6. Show the connection of two 741 op-amp stages to provide outputs that are 15 and -30 times larger than the input. Use a feedback resistor, Rf = 150 kQ, in all stages.
Given the following amplifier with feedback circuits A, B, C and D shown below... Assuming circuits A and C share the same feedback topology, determine their feedback topology. Assuming circuits B and D share the same feedback topology, determine their feedback topology. Determine whether each circuit utilizes positive or negative feedback. Note: For questions asking for feedback topology, answers can only be shunt-shunt, shunt-series, series-series or series-shunt
Vs RE www 2₁ www Rc1 11 Vcc RC2 Q₂ RF Q3 +₁ -O V₂ Sketch the feedback small signal model of this circuit.
The circuit shown in Fig. 4 provides transfer characteristics with +7.5 V levels at the output vo. When v 0 V, a current of 0.5 mA flows in the feedback resistor (R2) and a current of 1.0 mA flows through the zener-diodes. Assume that the output saturation levels of the op-amp are ±12.0 V, the forward-drop voltage of the zener-diode is 0.7 V, and the value of R, is equal to R2. a) Specify the zener-voltages of the zener diodes. b) Find the values of all resistors. R2 R1 R Z Z, Fig. 4
Compare the closed-loop voltage gain, k = Vo/Vs, for the loaded and unloaded dependent source model of the Voltage Follower with the ideal model of the Voltage to examine the impact of the load, RL on k. - Using any circuit analysis method, derive expressions for the closed-loop gain, k = Vo/Vs, for the ideal opamp Voltage Follower ,both the unloaded ,loaded Voltage Follower using the dependent source model. simplify both of the closed-loop gain expressions for the dependent source models by applying the ideal opamp parameters: A --> infinity , R_i -->infinity and R_0 --> infinity.
Şe s deve e R yuk utrerncinin ak reguamekteor. M. deyamua kalacak şekinos ie maksimum dečerini hesapie The current of a load resistance Rp is regulated with the feedback circuit shown in the figure. The Mosfet operates in saturation. What is the maximum value of Rp while M, remains in saturation? Circuit parameters / Bevre Perametreleri VREF=2.8 V, Rs=100 , w/L=54/0.18, VoD = 41 V, H,Cox = 200 µA?, VTH = 0.4 V, A = 0, A, = 00. VDD I. * RD A1 VREF Rs O a. 15.96 k O b. 23.94 k O c. 18.62 kn O d. 13.30 kn O e. 7.31 ko O f. 21.28 kO O g. 9.97 kn O h. 4.65 kn WH.