(a) Consider buck-boost converter with the following parameters: Vin=40 V, Vo =60 V, R=20 N, and L=750 μH. (a) Determine the duty cycle? is this converter operates as a buck or a boost converter ? (b) Calculate IL,min and IL,max

Q: 81 What is the function of the zero-adjust control in a multimeter. it serves to conduct the current…

A:

Q: What code sets standards for electrical installation and related works?

A: In this case, the code that sets standard for the electrical installation and related works is to be…

Q: Under what circumstances the power transformer will act as a source of harmonic? Rated load contion…

A: The transformer operated in no load or lightly loaded condition it produces harmonics. Due to no…

Q: How does the load power vary with the load resistance

A:

Q: Briefly describe the major difference between HEC and CLP regarding the connection from the…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Any change of the Components currents references will not affect the resulting current values, why?

A: we need to know why any change of the Components currents references will not affect the resulting…

Q: Define the following terms Density Physics Mass Power Law of Conservation of Energy.

A:

Q: What is the use of the tool marked in the figure? Tools A. To cut the wire B. To joint two wires C.…

A: The tool marked in the figure is,

Q: What are the protection coordination procedure of circuit breakers

A: Protective Devices MOV (Metal Oxide Varistor) fuse Circuit Breaker Relay Lighting Arrester Inrush…

Q: Clear print on the keyboard and correct or dislike  In regards to the model of a real transformer,…

A: Transformer is an ac static electrical device that transfers electrical energy from one electrical…

Q: overcurrent protection

A: Given :- Transformer rated at 1000V,              Primary overcurrent protection device is at 250%…

Q: help please answer in text form with proper workings and explanation for each and every part and…

A: 1. Shielded Metal Arc Welding (SMAW) / Stick WeldingProcess: Uses a consumable electrode coated in…

Q: A welding power source must not be used continuously in long time without care. The rated duty cycle…

A: A transformer-style welding power supply converts moderate voltage, moderate current electricity…

Q: **************************** SUBJECT = Electric Machines ****************************** Q  A…

A: Solve as below

Q: dentify the test used to measure the copper losses of the transformer. With necessary diagram…

A: For finding the copper losses of transformer we do short circuit test as explain below in step 2

Q: Question No.11. Which of the following best describe the arrow A shown in welding diagram below…

A: In the shown in the figure Best describe the arrow in welding diagram?

Q: Question No.9. In Arc weldingcoated electrode provide any of these Tunctions except heat sourc…

A: The explanation is as follows.

Q: Adopt a customer perspective and state what features of circuit breakers are critical to quality…

A:

Q: Are sums of components’ powers equal to zero? Why? 8. Resistors convert electrical energy to what…

A: The sum of powers of all components is equal to zero because in a circuit there is a source and…

Q: Explain the concept of load shedding and provide examples of situations where load shedding might be…

A: Load shedding is a controlled and intentional reduction of electrical power supply to specific areas…

Q: What is factor of a cable at 5 degrees celcius when calculating resistance

A: The solution is provided in the following section.

Q: Soldering is an example of O a. Heat treatment process. O b. Material removal process. O c. Joining…

A: Soldering is a joining and assembly process.

Q: 5 Choose the reason for a huge Loading effect, during the current measurement using an ammeter. a.…

A: In most of the ammeters an accurate and very low value resistor is used as a sensing element. This…

Q: Can a full adder circuit be used as a subtractor? If yes, draw the circuit (please ASAP TIA)

A: A full adder is a circuit that can be used for the summation task and a subtractor is used for the…

Q: Draw the resistor schematic symbol. What is the reason of the materials resistance in the circuit?…

A: In these question we have to give resistance symbol ,reason behind resistance and it's SI unit.

Q: (i) The full-load current, (ii) The full-load copper losses, (iii)The full-load efficiency, (iv)The…

A: The DC shunt generator has,  Terminal voltage Vt=450 V Armeture resistance Ra=0.75 ohm Shunt field…

Q: Identify the power system component represented by the given symbol. O fuse O Lightning arrester O…

A:

Q: 24 * Which of the following will not affect the resistance of the wires in the electrical circuit…

A: The resistance of a wire is directly proportional to resistivity of the wire and length of the wire…

Q: O a. The amount of energy transferred is dependent on the rotor size and the wind speed. O b. The…

A:

Q: While discussing the DC-DC converter used in most hybrids : Technician A says that it changes some…

A: Given a DC-DC converter used in hybrids Technician A says that it changes some of the DC voltage…

Q: In voltage regulators, Zener diodes are used to operate in Select one: a. Reverse mode b. Forward…

A: In forward mode zener diode just acts a normal diode and offers a small forward voltage drop In…

Q: What is The prime mover and conversion of  power in the hydro power station

A: The prime mover and conversion of  power in the hydro power station is-

Q: Draw the schematic diagram of the following.

A: Introduction: In a single-phase supply, there are mainly two conductors:  Phase wire: The phase…

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: 2. Figure 1 shows a voltmeter connection with 15 kO/ sensitivity, connected across Rb. Calculate the…

A: The solution is given below

Q: Which Arc Extinction Method operates by keeping the Arc Resistance low until the Current becomes…

A:

Q: 5. The resistance of a series field diverter should be a. comparatively high. b. equal to the…

A: The series field diverter are used to control the speed of a dc series motor above base speed. The…

Q: ay you display this in a circuit schematic?

A:

Q: A thermal power station has a boiler efficiency of 85% and turbine efficiency of 90 %. The thermal…

A: Given, A thermal power station has, Boiler efficiency, ηboiler=85%. Turbine efficiency,…

Q: Which type of the following solar system will not have solar tracking mechanism All of the options…

A:

Q: Identify whether each of the pole–zero diagrams shown in the image provided represent a stable…

A:

Q: I have 2 VRF heat recovery units with specs as follows: RLA = 0.2 %3D V = 208 PH = 1 HZ = 60 How…

A: As from given data, VRF heat recovery units are working on 208 V, single phase Therefore no.of poles…

Q: 2. For the following checks you should do with an ohmmeter before connecting power, what results…

A: Ohmmeter- An ohmmeter is an instrument used for measuring resistance it can be connected in series…

Q: Introduction of Geothermal Energy and Geothermal PowerPlant

A: Geothermal Energy   It refer to the energy that is derived from the natural bheat of the Earth.They…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.