A conductor whose diameter is 0.175inch has a resistance of 0.50. The wire is drawn through a series of dies until its diameter is reduced to 0.08inch. Assuming the specific resistance of the material remains constant, what is the resistance of the lengthened conductor? A) 11.452 B) 10.220 12.750 D) 10.820

A conductor whose diameter is 0.175inch has a resistance of 0.50. The wire is drawn through a series of dies until its diameter is reduced to 0.08inch. Assuming the specific resistance of the material remains constant, what is the resistance of the lengthened conductor? A) 11.452 B) 10.220 12.750 D) 10.820

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

temperature rating that a conductor must have and still have 69 Ambient Tempere 4. The ampacity of 15 current-carrying 10 RHW aluminum conduc- tors in a raceway in an ambient temperature of 75'F is 1. gon factor for conductor ampacity in this location is (a) 12A (b) 15A (c) 22A (d) 30A 0.71 b0.82 0.88 0.96 5. Ain) uous load if the ambient temperature is 75°F and there are nine THHN conductor is required for a 19.70A noncontin- ne ambient temperature is 71"C, the minimum insulation current-carrying conductors in the raceway in a dry location. he capacity to carry current is (a) 14 (b) 12 (c) 10 A 60°C AI 90°C 105°C (d) 8 0 120°C 6. 6.11 Ampacity Adjustment [310.15(B)(3)(a)] The ampacity for each of nine current-carrying 10 THW conduc- tors installed in a 20 in. long raceway is 1 The ampacity of six current-carrying 4/0 XHHW aluminum con- ductors installed in a ground floor slab (wet location) is (a) 25A (b) 30A (c) 35A (d) 40A a) 135A 0) 144A (e) 185A 4 210A
If the cross sectional area of a conductor is doubled, then the resistance of the conductor remains the same. becomes half of the initial value. becomes double the initial value. becomes four times the initial value.
Consider a three-core, three-phase, 50 Hz, 11 kV cable whose conductors are denoted as R, Y and B in the figure. The inter-phase capacitance (C₁) between each pair of conductors is 0.2 µF and the capacitance between each line conductor and the sheath is 0.4 µF. The per-phase charging current is C₂ HE C₁ ,C₁ Outer Sheath
Amagnetic field is being generated by a current of 2.0A flowing through 180 turns of wire on a core having a reluctance of 210000.0 At/Wb. Determine the flux of the circuit in mWb.
5) This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course. just write for me the the correct answer.
3. A coil consist area ot 0.8 mm? The mean 2.000 turns of copper wire haU ing length par copper is 0.02 MICD ohm -m. Find' the resistance absor bed by the coil when connected acoss lov de rupply. sectional a crass - turn is 0o cm and the rerictivity the coil and . power
maq Q1
Each of the conductor in a parallel-plate capacitor is calleda. dielectricb. insulatorc. platesd. terminal
Question 1 Select all that apply. Which of the following are considered to be "core losses"? 12R heating loss Flux lines that bulge out at core gaps Currents that circulate within the machine non-ferrous components Field Lines that circulate around conductors and coils Rapid Changes in Domain orientation
The property of insulating material which makes the breakdown voltage high in a cable is ...... Good Mechanical strength O High conductivity O High dielectric strength O High insulation resistance
A coil that con sists of 450 windings is wound aroundabakelite ring. The mean diameter of the ring is 100 mm and the diameter of the bakelite core is 20 mm. The currentthrough the coil is 3 A. Determine: 1.1 a) the field stren gth b) the flux den sity c) the total flux A ringhas two halves. The onehalf is made from Cast iron, while the other is made from Cast steel. The two halves are held 1 mm apart with the aid of a paper disc. The cross-section al area and mean circumference of the ringis 345 mm? and0.6 m respectively. Therelative permeability of cast iron is 2400, while that of cast steel is 600. The ring has a coil with 200 win dings. The currentflow through the coil causes a flux den sity of 0.48T. 1.2 Calculate the: a) mmi b) currentflow Ignore the effects of fringing andleakage.
QUESTION 2 a) The total AAC cross sectional area is 544.7522 x 106 m2. Each strands having a radius of 0.34 cm and length of conductor is 2 m. Assume that the increase in resistance due to spiraling is 1.4 %. Given the resistivity of AAC at 20 °C is 2.83 x 10* Qm and T = 228 °C. Determine the total composed strands and DC resistance at 30 °C. b) Figure 2 shows the configuration of a single-phase two-conductor in the transmission line. Calculate the total inductance "Ltotal" of the line. (Given, rx = 0.02 m and ry-0.03 m) 3' 1.20 m 0.22 m 2.09 m 0.44 m 2" Conductor 'x' Conductor 'y' Figure 2