A concrete masonry unit was tested according to ASTM C140 procedure andproduced the following results:mass of unit as received = 8271 gsaturated mass of unit = 8652 goven-dry mass of unit = 7781 gFor this unit, calculate (a) absorption in percent and (b) moisture content as apercent of absorption.

Q: Why is it important that the concrete masonry units meet certain absorp- 811 a tion requirements? h…

A:

Q: Calculate the volumes of the hydration products for 150 gm of cement with 0.5 w/c ratio, assume…

A: It is required to determine the volume of dry cement actually hydrated. Vcah=Weight of dry cement…

Q: A trial concrete mix is to be prepared for a garage floor which is subjected to freezing. and…

A: Solution: Concrete Mix Design: The required strength = 32 MPa Standard Deviation = 1.5 Coarse…

Q: A concrete masonry unit is tested for compressive strength and produces the following results:…

A: Given, P = 120000 lb Ag = 130 in2 Vg = 960 in3 Vn = 447 in3

Q: y consider the following data for concrete with mild exposure, calculate the quantity of cemer…

A: Given:Volume of water=191.6 litreWater cement ratio=0.5

Q: A sample unit of concrete masonry is recieved having a mass of 10.4kg. The unit is tested using ASTM…

A: Given: The received mass of units is 10.4 kg. The standard mass of the unit is 11.1 kg. The dry mass…

Q: A trial concrete mix is to be prepared for a garage floor which is subjected to freezing. and…

A:

Q: The name of the test used to measure the consistency and workability of fresh concrete is called the…

A: The name of the test used to measure the consistency and workability of fresh concrete is called the…

Q: 1. (a) The data presented below is compiled to obtain the modulus of rupture values of the MgO…

A:

Q: (b) All basic chemical composition of Portland cement reacts with different rate of hydration. List…

A:

Q: nstruction: Please provide complete solutions and box final answers.

A: S.no  Strength in Mpa  Mean  (X-mean) (x-mean)^2         1 38.3 41.735 -3.435 11.799225   3.074275…

Q: Compare the setting time of a Portland cement and pozzolan cement? Provide a thorough discussion.…

A: When compared the setting time of Portland cement and pozzolan cement, the initial setting time of…

Q: Please perform an experiment and provide a report on Air Content of Freshly Mixed Concrete by…

A: Answer:- Test equipment:- ASTM C231 along with following: 1. Tamping rod:- has 18 inch length and…

Q: Mixing and handling can significantly alter the air content of fresh concrete. Thus, field tests are…

A: Air entrapped concrete is used generally in areas with low temperatures and damages can occur due to…

Q: A concrete masonry unit tested as follows: 8,893 g 9,354 g Determine the absorption and moisture…

A: Given: The saturated mass is 10,089 g. The oven dry mass is 8,893 g. The field mass is 9,354 g.

Q: 4) Design a concrete mix for the following condition and constraints using the absolute volume…

A: The given data is: Design strength=27.6 Mpa Standard deviation=4 MPa Assuming the following: Target…

Q: Design the concrete mix according to the following conditions: het Design Environment Pavement slab,…

A: Given, Design strength (f'c) = 5000 psi  Admixture dose = 0.15 fl oz/1% air/100 lb

Q: When conducting a laboratory test on brick samples, the following results were obtained: 8…

A: According to the Iraq standard no.25, The grades of bricks can be classified into three grades. They…

Q: A concrete masonry unit was tested according to ASTM C140 procedure and produce the following…

A:

Q: From the knowledge of the effects of GGBS, PFA and microsilica, indicate whether their inclusion to…

A: Required to find: How the presence of GGBS, PFA and microsilica effect the  a) Alkali silica…

Q: Design a concrete mix for the following conditions and constraints using the Absolute Volume Method.…

A: Given  Required Design Compressive Strength (f'c) = 27.6 MPa Standard Deviation of Compressive…

Q: MAKE A CONCLUSION ABOUT THE SPECIFIC GRAVITY OF CEMENT

A:

Q: Calculate the average density of brick. ?

A: Brick No. Length mm Width mm Depth mm Mass kg 1 213 98 70 2.52 2 212 98 70 2.5 3 211…

Q: A portion of a normal-weight concrete masonry unit was tested for absorption and moisture content…

A: ASTM C140  Mass of unit as received, Mo = 7024 g Saturated mass of Unit, Msat 7401 g Oven-dry mass…

Q: Controlling excessive temperature gradients in large concrete masses is very crucial. Explain in…

A: After the placement of the concrete, monitoring the temperature of concrete is one of the most…

Q: Q2. Design the concrete mix according to the following conditions: Design Environment: Building…

A: Given Required design strength = 21.9 MPa Minimum dimension = 150 mm Minimum space between rebar =…

Q: A concrete masonry unit was tested according to ASTM C140 procedure and produced the following…

A: Solution:-

Q: If the moisture content of coarse aggregate is lower than the absorption, the water needs to be…

A: Water absorption Water absorption of aggregate is a measure of porosity. This value is considered as…

Q: a) How many unknown displacements are in the displacement vector? b) How many the displacement…

A: From the given Structure :

Q: Explain pozzolanic reaction with hydration products and its effects on hardened concrete properties

A: Pozzolanic material are siliceous and aluminium material in which themselves posses little or no…

Q: concrete

A: Answer:-

Q: rding to the following conditions. Design Environment Pavement slab, (cold climate) Required design…

A: Given : Required design strength = 3000 psi Slab thickness = 12 in. Statistical data indicate a…

Q: Design a concrete mix for the following conditions and constraints using the Absolute Volume Method.…

A: Following is required answer : NOTE : Due to guidelines, first 3 parts are necessary to answer.

Hydrogen Energy

Energy is a quantity that cannot be defined, its existence can only be felt. In simple language, if a system possesses energy, it can do a specific kind of work. There are many forms of energy sources which people can use to obtain work. Solar energy, tidal energy, hydroelectric energy, geothermal energy, wind energy are some of the renewable energy sources which are primarily used for the production of electricity.