A computer production company "HP" wishes to produce three types of electronic devices type A, B and C. To manufacture a type A device requires 4 minutes each on machine I, 2 minute on machine II and 4 minutes on machine III. A type of B device requires 2 minute on machine I, 6 minutes on machine II and 2 minutes on machine III. A type C device requires 2 minutes on machine I, 4 minutes on machine II and III. There are 6 hours available on machine I, 10 hours available on machine II and 8 hours available on machine III. Using appropriate command calculate the number of devices of each type should company make in order to use all the available time.

A computer production company "HP" wishes to produce three types of electronic devices type A, B and C. To manufacture a type A device requires 4 minutes each on machine I, 2 minute on machine II and 4 minutes on machine III. A type of B device requires 2 minute on machine I, 6 minutes on machine II and 2 minutes on machine III. A type C device requires 2 minutes on machine I, 4 minutes on machine II and III. There are 6 hours available on machine I, 10 hours available on machine II and 8 hours available on machine III. Using appropriate command calculate the number of devices of each type should company make in order to use all the available time.

Operations Research : Applications and Algorithms

4th Edition

ISBN:9780534380588

Author:Wayne L. Winston

Publisher:Wayne L. Winston

Chapter3: Introduction To Linear Programming

Section: Chapter Questions

Problem 40RP

See similar textbooks

Similar questions

I need the answer as soon as possible
Two rail roads and junction for two trains (T1 and T2) that move in opposite directions as shown in the following figure. An asynchronous state machine is used to control the motion of trains in the junction. It is worth to mention that the long of each train is 1.25 km, the maximum speed of each train is 300 km/h, and the first train departs before the second train by one hour at least. The distance between A and B is 0.75 km. How many states are required to draw a minimal Moore state diagram for the asynchronous state machine that controls the motions?
Which of the following is one of the three characteristics that are sought when it comes to the electrical power supplying IT equipment? Maximization of circulating current Reduction of the grounding circuit Increase in electromagnetism  Minimization of electrical noise Which of the following is a condition that must be met in order to qualify for the exemption from grounding requirements? The installation is in contact with ground and other conductive material. The runs are in lengths more than 25 feet long.  The circuits contain an equipment grounding conductor. The installation is guarded from contact by people. Installations of computer circuits for IT centers typically include isolated/insulated grounding circuits derived from power distribution units.  signal reference grids.  sensitive electronics.  broadband grounding systems.
An iron rod is graded based on the following criteria: Magnetite content must be greater than 50 Calcium carbonate must be less than 0.7 Other adulterants must be greater than 5600 The grades are as follows: Grade is A if all three conditions are met. Grade is B if conditions (i) and (ii) are met Grade is C if conditions (ii) and (iii) are met Grade is D if conditions (i) and (iii) are met Grade is E if conditions only one condition is met Grade is F if none of the conditions are met. Write a program in which you ask user to enter the values of Magnetite, Calcium Carbonate and other adulterants. The output will be generated as per the conditions mentioned above. (Put the visible screen shots of the output with 2 to 4 different input variations)
solve pls in excel
Ina de chopper, the average load current is 30 A, chopping frequency s 250 Hz. Supply voltage is 110 volts. Calculate the ON and OFF periods of the chopper if the load resistance is 202.
C language programing question
A certain grade of steel is graded according to the following condition: 1. Hardness must be greater than 40 2. Carbon contents must be less than 0.8 3. Tensile strength must be greater than 5000 The grades are as follows: § Grade is 10 if all the three conditions are met. § Grade is 9 if conditions 1 and 2 are met. § Grade is 8 if conditions 2 and 3 are met. § Grade is 7 if conditions 1 and 3 are met. § Grade is 6 if only one condition is met. § Grade is 5 if none of the conditions are met. Write a C++ program which will require user to give values of hardness, carbon content and tensile strength of the steel under consideration then determine the grade of steel and outputs the grade of the steel
For the circuit shown below, find the nodal voltages Vi, V, and V; 20 Ohms v | 1oomms V2 400hms |v 13— [ ANV s YO §500th (1)2A Nl i SEP
M D d T M. P- A circular shaft having diameters D and d and a groove of radius r (with M = 0 and P O) is made of steel with the allowable shear stress tall. Find the maximum torque I that can be transmitted by the shaft. Given: D = 28mm, d = 20mm, r = 4mm, and tall = 250 MPa. Please help with this question. The answer should be 157.1 Nm
XYZ Company manufactures pressure relief inserts for thermal relief and low-flow hydraulic pressure relief applications where zero leakage is required. A machine purchased 3 years ago has been book-depreciated by the straight line method using a 5-year useful life. If the book value at the end of year 3 is $30,000 and the company assumed that the machine would be worthless at the end of its 5-year useful life. What is the book depreciation charge each year.
G1