A computer circuit board dissipates 0.1 KW from one side over an area 300 mm by 200 mm. A small turbo fan cools the computer with flow speed of 12 m / s. It is of utmost importance that the circuit board is kept within acceptable temperature range. Using the average Nusselt number relationship Nusv = (0.05RE 0.8 – 310) Pr3. You are required to calculate: %3D

A computer circuit board dissipates 0.1 KW from one side over an area 300 mm by 200 mm. A small turbo fan cools the computer with flow speed of 12 m / s. It is of utmost importance that the circuit board is kept within acceptable temperature range. Using the average Nusselt number relationship Nusv = (0.05RE 0.8 – 310) Pr3. You are required to calculate: %3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.19P

See similar textbooks

Similar questions

Q1: Consider a wall heated by convection on one side and cooled by convection on the other side. Show that the heat-transfer rate through the wall is T1-T2 1/h A+A/kA+ 1/h2A Where T; and T; are the fluid temperatures on each side of the wall and h, and h; are the corresponding heat-transfer coefficients.
350 pipes are fixed as square in a pipe bundle used for condenser. PipeThe outer diameters are 8 mm and the steam at 0.2 bar is desired to be condensed on the pipes. pipe outer The surface temperature is kept constant at 30 °C. If the length of the pipes is 1.5 m, the heat transferred in the systemCalculate the amount of energy and the amount of condensed steam
A 2m^2 wall of 1010steel is 8 mm thick. If the outside of the wall is100 °C, andyou measure aheat flux of 80 kW/m2coming off the wall, what is the temperature of the insideof thewall?
Q2/ An aluminum sphere weighting 7kg and initially at a temperature of 533K is suddenly immersed in a fluid at 283K. if heat transfer coefficient between the sphere and fluid is 50W/m?.°C. Take density=2707kg/m3, specific heat=0.9KJ/kg.°C and thermal conductivity= 204W/m °C. إجابت * Determine the Bi number 0.00696 0.000696 0.0052 0.00052 0 أخری *.Determine the time required to cool sphere to 263K 26.28min 262.8min 52.56 min 525.6 min O أخری
A chromel–constantan thermocouple measuring the temperature of a fluid is connected by mistake with copper–constantan extension leads (such that the two constantan wires are connected together and the copper extension lead wire is connected to the chromel thermocouple wire). If the fluid temperature was actually 250 C and the junction between the thermocouple and extension leads was at 90 C, what e.m.f. would be measured at the open ends of the extension leads if the reference junction is maintained at 0 C? What fluid temperature would be deduced from this (assuming that the connection error was not known)?
For a water flow over a steel surface, the temperature of water at a specific location was found to change with the vertical distance from the surface (y) up to a distance of 0.015 m as T(y) = 60 + 20y + tan(y), where temperature is in °C and y is in cm. The surface temperature and ambient temperature was measured as 60°C and 105°C, respectively. The thermal conductivity of steel and water are, respectively, 48 W/m-K and 0.6 W/m-K. What is the local convection coefficient at this location?
Water is entering a heated tube at mass ow rate of 1.2 kg/s. The temperature at the inlet is 20 C and at the outlet is 80 C. Assume the surface temperature of the tube is 100 C. The convection coe cient of the water ow is 28 W=m2 C. The speci c heat and density of water can be assumed to be 4180 J=kg C and 990 kg=m3. What is the rate of heat transfer to water during this proces
How much heat is conducted through a sheet of plate glass, k=0.0024 cal/cm2-sec-°C/cm, which is 2.0 meters by 3.0 meters and 5 mm thick, when the temperatures of the surfaces are 20 and -10°C? COMPLETE FBD SOLUTION AND REQUIREMENTS PS. THIS IS A HEAT TRANSFER PROBLEM
Answer this ASAP The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg. °C. The overall heat transfer coefficient is 0.7 kW/m².°C. 1.Cmin 2.Maximum heat transfer rate 3.Heat transfer surface area
Answer this ASAP The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg.°C. The overall heat transfer coefficient is 0.7 kW/m².°C. 1. Schematic of temperature distribution 2.ΔTLMTD 3.Actual heat transfer rate 4.Cmin 5.Maximum heat transfer rate
(heat transfer ) thanks The velocity of the fluid flowing in parallel over a 500mmx500mm flat heater surface is U= 19 m/s and the inlet velocity temperature is T_∞15 C. The surface temperature of this plate is T_s140 C, the friction force is F_D=0.4 N and the surface area of the plate is A=0.32 m2. According to this;(F_D= 0.4N A=32 m2)a) Surface shear stressb) Find the coefficient of frictionc) Heat transfer coefficientd) What is the amount of heat transfer (electric power) that must be given to maintain a constant surface temperature?
Wind blows over a whirlpool hot tub. The air temperature is 290 K with a convection heat transfer coefficient equal to 400 W/m-m- K. The water temperature is 315 Kwith a convection heat transfer coefficient equal to 450 W/m-m-K. Report the temperature at the surface of the water in units of Kand using 4 significant digits. Note that the error band on this answer is 0.5%. Type your nunmeric answer and submit