A compressor draws in 500of air whose density is 0.079lband dischargesminlbit with a density of 0.304ft³At the suction, P1 = 15in?and at the discharge,lbThe increase in the specific internal energy is 33.8Btuand thelbP2 = 80in?Btuheat from the air by cooling is 13 . Neglecting changes in the potential andlbBtukinetic energy determine the work done on the air inminand in horsepower.

Given that, Volume flow rate of air in compressor at entry, v˙=500 ft3/minDensity of air at…

A compressor draws in 500 min of air whose density is 0.079 and discharges it with a density of 0.304 - At the suction, P1 = 15 and at the discharge, in? Btu and the lb P2 = 80 The increase in the specific internal energy is 33.8 Btu heat from the air by cooling is 13 Neglecting changes in the potential and lb kinetic energy ermine the work done on the air in min Btu and in horsepower.

A compressor draws in 500 min of air whose density is 0.079 and discharges it with a density of 0.304 - At the suction, P1 = 15 and at the discharge, in? Btu and the lb P2 = 80 The increase in the specific internal energy is 33.8 Btu heat from the air by cooling is 13 Neglecting changes in the potential and lb kinetic energy ermine the work done on the air in min Btu and in horsepower.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pls. Answer this..? A steam engine has 10% brake thermal efficiency and consumes 750 kg/hr steam. The enthalpy of steam at the entrance ang exit of the engine and condenser are 2800 and 450 kj/kg repectively. Determine the brake power of the engine in kw.
I need the answer as soon as possible
A large water pump takes water from a nearby lake at a rate of 35 f/Sec and rauses its pressure from 7 to 100 psia, with a negligiblymall change in the speific ntermal energy iand the density, So that if can be fed into an rngahon Systemo if the pump isG adiabatic and frictionless, delermine the magnitude of the power necessary to drive the pump in hp using 5 signifigant figures. Hint: you need to use an equation for h.
3.) An air compressor handles 8.5 m’/min of with a density of 1.26 kg/m³ and a pressure of 1 atm, and it discharges at 445 kPa (gage) with a density of 4.86 kg/m³. The change in specific internal energy across the compressor is 82 kJ/kg, and the heat loss by cooling is 24 kJ/kg. Neglecting changes in kinetic and potential energies, find (a) the work in kJ/kg and (b) the power in kW.
I need the answer as soon as possible
17. A fully inflated tire has a volume of 15 ft3. The pressure and temperature of theair in the tire are 65 psia and 75 F, respectively. At this condition, the air intakeneedle is depressed for 3 s and then released. Treating air as an ideal gas and assumingsmall changes in the tire temperature and volume, Find the amount of air that leftthe tire. Assume a discharge coefficient of 0.61 and a flow area of 0.01 in2.
Steam generators are a type of heat exchanges that are used inpower plants to generate steam at desired pressure andtemperature (Fig. Q1.b). In a steam generator, saturated liquidwater at 30°C enters a 60-mm diameter tube at the volume flowrate of 12 L/s. After exchanging heat with hot gas, the waterchanges to steam and leaves the generator at a pressure of 9 MPaand a temperature of 400°C. During this process, the diameter ofthe water/steam tube does not change. Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). (i) Calculate the steam mass flow rate and inlet velocity of the steam? (ii) What is the exit velocity of the steam? (iii) Calculate the rate of heat transfer (in MW) required tochange the phase of liquid water to steam.
Solve please, correctly
A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid, At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60m's. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (a) Find the velocity at the nozzle exit. (b) If the inlet area is 0.1 m’and the specific volume at the inlet is 0.19 m²/kg, find the rate of flow of fluid (C) If the specific volume at the nozzle exit is 0.5 m kg, find the exit area of the nozzle. Dr. Hameed J. Khalaf Subject Lecture
Explain the steps in simple way so that i can understand the problem. Kindly don't use Ai ,It is Important one.
pls correct the given this is my last attempt thanks
Identify what is the system in this problem and write the general energy balance equation (no need to solve) A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the specific delta H?