A compound tube consists of a steel tube 120 mm internal diameter and 140 mm external diameter and an outer brass tube 140 mm internal diameter and 10 mm thickness. The two tubes are of the same length equal to 150 mm. The compound tube carries an axial load of 800 kN. Estimate the stresses and the load carried by each tube and the amount it shortens. Take E for steel as 2 × 105 N/mm2 and for brass as 1 × 105 N/mm2.

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

A:

Q: Q7-Q8: A 6-in.-long bronze tube, with closed ends, is 3 in. in diameter with a wall thickness of…

A: Longitudinal Stress, σlong = σx = 15 ksi. Tangential Stress, σtang = σy = 45 ksi.

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: The one end of a hollow square tube whose side is 10.47 in with 1.47 in thickness is under a tensile…

A: Cross section of the bar,Hollow square tube, a=10.47 inchthickness, t=1.47 inchtensile stress on…

Q: Calculate the maximum shear stresses from the torsional moment it the shaft between the points B and…

A:

Q: Find the stresses at point C. -1.5 m 2.5 m 250 mm 125 mm 1.5 m 50 kN/m 50 mm 2 m 4m

A: Find the stresses at point C.

Q: This is a question from the textbook, Example 3.1 from page 132. We are interested in the…

A:

Q: Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Mpa steel bronze A= 300mm2…

A: Given: The maximum allowable stress in steel rod = 120 MPa The maximum allowable stress in bronze…

Q: A steel pipe assembly supports aconcentrated load of (P = 22 kN) as shown in Figure. The outside…

A: Calculate the moment about point H due to load P.   MH=P370 mm×1 m1000 mm=22 kN×1000 N1 kN370 mm×1…

Q: 100 kip 10 kip-ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of…

A: solution Given d=4 in

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Given data: -  The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…

Q: A pressurized pipe with an outside diameter of 14.35 in. and a wall thickness of 0.25 in. is…

A:

Q: Calculate the tangential stress in the steel.

A: Given that ,  R=250mm  t=20mmP=4.5MN/m2  =4.5×106N/m2

Q: The maximum shear stress (in MPa) in the

A: Given;  A cylindrical tank of;  Inner radius,r=7 mm  Thickness=50 mm  Gauge pressure= 2 MPa…

Q: pipe wrench Pipe (eylinder)

A: In this problem 2 forces exerted on shaft. Due to the force P bending stress will occur in shaft…

Q: A circular shaft is subjected to combined loads of bending M and torque T. With the help of Mohr's…

A: Circular shaft is subjected to combined loads of bending M and torque TNow,Bending stress induced in…

Q: 3. Compute the shear stresses. At the top of the side wall the thickness, 1, is 24 in. The torsional…

A:

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 320 mm and a wall…

A:

Q: 2. A hollow generator shaft of 180-mm outer diameter and 120-mm inner diameter carries a torque T 40…

A:

Q: stress in the segment QR

A: Given; A bar having cross-sectional area(A)=700 mm2Various loads at the positions indicated at the…

Q: Q2/ Find the diameter of steel rope required to lifting a machine of 3.25 tones weight safely, if…

A:

Q: PROBLEM 2. The forces shown in the figure are applied to a plate connected to a pipe with an outer…

A:

Q: Problem 2.2 Consider the following load raising system. a) Calculate the power of the motor if the…

A: Given figure  To calculate  (a)Calculate the power of the motor if the load is to be raised at a…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: Find the longitudinal stress in the tank.

A: To Find the longitudinal stress.

Q: 80 MPa 60 MPa

A: Consider the given plane figure on x-y plane. From the figure, Stress in x direction = σx = 0 MPa…

Q: A cylindrical hollow tube with closed ends is pressurized to a gauge pressure of 10 MPa and twisted…

A:

Q: = A machine component is fabricated from a bent tube as shown below. One part of the tube lies along…

A: Outside diameter, d0=122 mmInside diameter, di=108 mmForce F=8.5 kNLengths,L1=258 mmL2=118 mmL3=281…

Q: subjected loads s.

A:

Q: Calculate the stress in the circumferential section of boiler steam drum 2.15 m in diameter and 45…

A:

Q: A pressure vessel with an internal pressure of 400 psi is fixed at one end. At its free end, two…

A: Px=10kipsPy=15kipsPz=5kipsD=10 ind=9.6 in

Q: 6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 1D…

A: force, F=σ×AF=3.5×π4×4302F=508270.42 NP=F

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.000 in. and a wall thickness of 0.125…

A: For solution refer below images.

Q: Calculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10…

A: Given  Pressure = 10 MPa Thickness of vessel = 38mm Hoops stress = 83MPa Pd/2t = 83 10d/(2×38)=83…

Q: Define the main difference between thick and thin cylinders and give an example for each type of…

A:

Q: holding oxygen at 2,058 kPa pressure has an outside

A: t/D= 13/393 Since value is less then 1/2/ So it is a thin cylinder

Q: The thin-walled pressure vessel shown was fabricated using a spiral seam. The inner diameter is…

A:

Q: A cylindrical steel pressure vessel 200 mm radius with a thickness of 20 mm, is subjected to an…

A: Given: P = 5 MN/m2 t = 20 mm r = 200 mm

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.