Q/ A composite wall is formed of a 2.5-cm copper plate (k = 386 W/m.°C), a 3.2-mm layer of 0.038 W/m.°C). The wall is asbestos (k = 0.16 W/m.°C), and a 5-cm layer of fiberglass (k subjected to an overall temperature difference of 560-C. Calculate the heat flow per unit area 1. Water flows at the rate of 0.5 kg/s in a 2.5-cm-diameter tube having a length of 3 m.A constant heat flux is imposed at the tube wall so that the tube wall temperature is40•C higher than the water temperature. Calculate the heat transfer and estimate thetemperature rise in the water. The water is pressurized so that boiling cannot occur.

Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

A composite wall is formed of a 2.5-cm copper plate (k = 386 W/m.°C), a 3.2-mm layer of 0.038 W/m.°C). The wall is asbestos (k = 0.16 W/m.°C), and a 5-cm layer of fiberglass (k subjected to an overall temperature difference of 560-C. Calculate the heat flow per unit area

A composite wall is formed of a 2.5-cm copper plate (k = 386 W/m.°C), a 3.2-mm layer of 0.038 W/m.°C). The wall is asbestos (k = 0.16 W/m.°C), and a 5-cm layer of fiberglass (k subjected to an overall temperature difference of 560-C. Calculate the heat flow per unit area

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The left side of a composite wall is kept at 300oC constantly. The right side of the same wall is exposed to air at 20oC with a convection coefficient of 32 W/mk. kA = 10 W/mK, kB = 40 W/mK, kC = 1 W/mK, kD = 300 W/mK, kE = 0.1 W/mK Given figure 1, calculate: a) The total thermal resistance of the wall.b) The total heat rate through the wall.c) The junction temperature where B meets D (between second and third column)
A pipe with 8 cm internal diameter, 9 cm outer diameter, 2 meter long, thermal conductivity 30W/mK is insulated by glass wool material with which thermal conductivity 0,05W/mK, thickness 4 cm. Internal surface temperature of the pipe T1 is 80°C, surrounding temperature where pipe is located is 20°C, convection heat transfer constant on outer surface of insulation is 25W/m?K. Kpo 30W/mk T.= 20°C h. = 25W/MK 4cm K= 0,05W/mK a. Detemine the heat loss from the pipe to surrounding (W)? b. What is temperature of the surface between glass wooden and pipe (T2)? c. What is critical insulation radius for pipe? Is insulation on the pipe succesful? Explain
Heat transfer
Q1: A house has a composite wall of wood, fiberglass insulation, and plaster board, as indicated in the sketch. On a cold winter day the convection heat transfer coefficients are h. = 60 W/m2. °C and h = 30 W/m2. °C. The total wall surface area is 350 m². Take k,= 0.038 W/m. °C, k,= 0.17 W/m. °C, k,= 0.12 W/m. °C, and k.= 0.026 W/m. °C. (a) Determine a symbolic expression for the total thermal resistance of the wall, including inside and outside convection effects for the prescribed conditions. (b) Determine the total heat loss through the wall. Glass fiber blanket (28 kg/m³), k, Plaster board, k, Plywood siding, k, Inside Outside Stagnant air space h, T= 20°C h, T. o = -15°c 11 11 Ka=0.026 W/m. C 10 mm - 100 mm 20 mm L,
You are designing a new eco-friendly thermal coffee mug. It is shaped like a small globe to minimize surface area, which is only about 0.04m^2. You use two 0.003m layers of recyclable PETE which has a thermal conductivity, k, of 0.2W/mK around a 0.01m layer of dead air, with a thermal conductivity of 0.026W/mK. Since this is for hot coffee, use a temperature difference of 40K. Q = Ax (T2-T1) / (R1 + R2 + etc) R =x/k. What is the heat lose through the surface in watts?
10.The layout of a wall and the heat transfer parameters are shown in the figure below. Find the internal temperature of the wall, T₁. (o= 5.67 x 10-8 W/m²K4 ) (Ans: 569.5K) T1 k=1.1 W/m.K Icond L=0.12m T2=373K x=0.7 grad Iconv Tsur Air Tex = 300K h = = 290K : 18 W/m².K
Need correctly..