a component is made of 6061 T6 aluminum sheet LT. A axial tensile stress of 50 ksi is applied at room temperature. Will the part yield? Why or Why not??

Q: Calculate the stress developed in a steel rod that is 25 mm in diameter when a 70kNaxial tensile…

A: Diameter of rod=d= 25 mm Cross- sectional area= A= (π/4)×d2 = (π/4)×252= 490.873 mm2 Axial load=P=…

Q: how did we go from 9.3kN to 7.5 kN for the load applied?

A:

Q: spring-mass system with m = 0.01 Mg and k = 5 kN/m is subjected to a harmonic force of amplitude…

A: m = 0.01 Mg = 10000 g = 10 kg k = 5 kN/m = 5000 N/m F0 = 0.25 kN = 250 N X = 100 mm = 0.1 m ω0 = ?

Q: A load of 22 kips is gradually applied to a 2-in round rod, 10 ft long. The total elongation is…

A: Given dataLoad = 22 kips = 97860.88 NDiameter of section = 2 in = 0.0508 mLength of rod = 10 ft =…

Q: A 10 mm diameter wire cable is being used to lift a crate of parts. If the cable is made from…

A:

Q: Stepped bar ABCD is fabricated out of three different materials and loaded as shown. The applied…

A:

Q: What is the influence of the strain on the triaxial stress if it is subjected to the material?

A: The strain of a specimen is defined as the deformation of specimen per unit length of that specimen.…

Q: How is the torsion test performed to determine the material’s ultimate shear stress?

A: A torsion test is a destructive type of testing used to find the properties of specimen under stress…

Q: Define the term Uniaxial stress?

A: When the stress is generated due to loading in one direction (along the axis of the loaded member),…

Q: Select the preferred diameter for an ASTM A227 cold-drawn wire that will have an ultimate tensile…

A: Given: A227 cold-drawn wire Ultimate tensile strength - 176 kpsi To find: Preferred diameter

Q: Calculate the stress developed in a steel bar that is 50 mm by 25 mm when a 70kNaxial tensile load…

A:

Q: The bars, shown in sketches (a) and (b), are made from cold-drawn, AISI 1050 QT at 425 °C medium…

A:

Q: You are asked to design a square steel bar out of ASTM A36 steel. The steel has yield strength of…

A:

Q: 4-3. Determine the residual strength diagram (ơmax versus a) for a center-cracked panel (CCP) of…

A: RESIDULA STRENGTH To lay out the remaining strength capacity of a given design under specific…

Q: 6. A cylındrical copper (E=110GPA) rod with length of 380mm, yield strength of 240MPA, is subjected…

A: Solution :- Given data :- E =110 GpaLoad P =66000 NLength of rod L =380 mm

Q: The figure below shows the stress-strain behavior of a mild steel (the insert shows part of the same…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: 4. The mechanical properties of a given titanium alloy (Ti-6Al-4V) are E = 114 GPa, σy = 880 MPa and…

A:

Q: The stress-strain relation shown in the Figure below was obtained during the tensile test of an…

A:

Q: If a key material has an ultimate strength of 120 ksi and a yield strength of 80 ksi and factor of…

A:

Q: If a key material has a yield strength of 80 ksi, and a safety factor N= 2, what would be the design…

A:

Q: 1) How much stress will be generated in the 13mm diameter aluminum rod below with an increase in…

A: Answer: The stress generated in the aluminum rod is 13.89 MPa.

Q: Calculate a diameter, d, to ensure that yield does not occur in the 1045 carbon steel (Yield stress…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.