A combinational logic circuit has three inputs with sequence A, B, and C and two outputs with sequence X and Y. The outputs XY represent a binary number whose value equals the number of .received 1s at the input

A combinational logic circuit has three inputs with sequence A, B, and C and two outputs with sequence X and Y. The outputs XY represent a binary number whose value equals the number of .received 1s at the input

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

allswer sheels A rain predictor circuit is designed based on four factors such as Presence of Cloud(A), Presence of Depression in the seatB), Cyclone formation in the seaC High Precipitation(D). A threshold is fixed for all the above conditions and if the above factors are above the threshold, that is indicated as logiio one and below the threshold is indicated as logic zero. The rain predictor will give a logic zero as output to indicate the probability for rain fall. The following conditions will hold it there is a probability for rainfall, (a) ifD alone is high (b) (A and C are zero and B and D are high )OR ( if A and D are zero and B and C are high) (c) fB alone is zero (d) if A and B are high and C is zero, then irrespective of the value of D, it will rain (e) If all parameters are high. (0 #A alone is zero, the circuit cannot predict whether it will rain or not. (g) For all the other conditions the circuit will predict high. Find out the simplified Product of Sum expression for…
Develop a simple program in C# that receives two binary inputs from the user (graphical or command line) and outputs the result of the selected gate operation. Gate operations that should be selectable are AND, OR, XOR.
design a circuit to implement a dynamicdisplay of two lights. and use several 2:1Mux, only one seven-segment display decoder andonly one 2:4 decoder
Computer Science A circuit for two output ports (A&C) of the AVR ATmega16 microcontroller each connected to 8 LEDs. Write a program to control the LEDs in a sequence shown by stepping to lit on the LED sequentially as in the figure by toggling the LED at the same time for both ports (500mS) ending at the last state of the figure and looping back inversely to the start. This s done for 3 times back and forth.
A combinational logic circuit has three inputs with sequence A, B, and C and two outputs with sequence X and Y. The outputs XY represent a binary number whose .value equals the number of received 1s at the input The designer needs for ...... conditional boxes for drawing the ASM-chart for the controller of the .aforementioned system 7 O 2 O 9 O 4 O 3 5 O
An 8x1 multiplexer has an output F; inputs A,B,C connected to the selectors S₂, S₁ and So respectively; and D is connected to the input as follows: 1₁-1₂-17=0; 13-15-1; 10-14=D; and I6=D' What is the boolean function (in sum of minterm format) that the multiplexer implements.
Computer Science 1. Design a circuit for a digital lock using the minimum number of D latches. The lock has two input push-button switches A, B and it outputs a single pulse (Z1) for each activation i.e. lock open. The two switches are interlocked mechanically so that simultaneous pulses are not possible. The lock should have the following features: a. The opening sequence is 0011. ii. Then replace ‘0’ by ‘A’ and ‘1’ by ‘B’ in the sequence. b. Five B pulses should give an absolute reset. c. Any incorrect use of the A switch will cause an output (Z2) to ring a bell to warn that the lock is being tampered.
A sequential circuit has three FF, A, B and C; one input x and one output y. The state diagram is shown below. The circuit is to be designed by treating the unused states as don't care conditions. Analyze the circuit obtained from the design to determine the effect of unused states. a. Use T FF in the design b. Use JK FF in the design. 0/0 001 1/1 0/0 1/0 100 011 0/0 1/1 1/1 \0/0 (010 1/1 000
The control logic of a synchronous sequential circuit will be designed with multiplexors. Given the state table, MUX inputs will be determined. What should be the value of the question mark in this table? Current State Next State Input G1 GO G1 GO MUX1 MUX2 10 10 la' 10 1 la 1 1 10 1 b' 1 10 ab 10 1 1 ab" 10 10 a'b 1 10 ? Oa' ab' b' 1. 1. 1.
9. A multiplexer is a switching circuit that produces as its single output one of a set of inputs based on the value of some additional inputs called the controls. Given that 0, 1, 2, and 3 in two-bit binary are 00, 01, 10, and 11, respectively, draw a 2-bit multiplexer using the three basic logic gates with inputs xo, x1, x2, and x3, and two control inputs co and c1. Setup the circuit so that x; is the single output, where i if the value of the 2-bit integer (cico)2. NOTE: This is not a Boolean product; instead it's the binary representation of an integer where c1 is the most significant bit and co is the least significant bit.
1a. Draw a circuit diagram using appropriate logic gates to implement a 3-bit comparator. Identifythe gates used in implementation and show its usage to compare two 3-bit words by writing thetruth table. b. Write the Boolean expression for the following 4 input circuit. Include sub-expressions foroutputs of each gate. c. Complete a truth table for the previous logic gate circuit in part b. d. Write the Boolean expression for the new circuit below. Then, simplify the following logic circuitusing the theorems in Boolean algebra. Show the steps clearly and specify the law used in eachstep. Finally draw the simplified circuit diagram.
In digital electronics and modern computer hardware, a flip-flop is sequential digital circuit used as a basic memory element. It has two stable states and can be used to store state information. One of its states represents ‘1’ while the other represents ‘0’. The most common types of flip-flops are SR-flip-flop, JK-flip-flop, and D flip-flop. When used in a finite-state machine, the output and next state depend not only on its current input, but also on its current state (and hence, previous inputs). Figure 1 D-Flip-flop with clock pulse (CP) Figure 1 shows a D flip-flop with clock pulse (CP). D is directly passed from stage1 to stage 2 through NAND gate and passed as inverted through gate 5 and gate 4. The input D is always sampled when the system CP is 1. Considering the memory element in Figure 1, perform the following tasks: Design FSM for the Figure 1 Simulate the Figure 1 using C. Write 400 words report on shift and…